CHAPTER 8 BAR CODE CONTROL - 5
3. DEFINITION OF PARAMETERS
This bar code command can have the following parameters in the parameter segment (n ... n). Parameters are
effective only within the single command sequence using the syntax ESC i n ... n \. They do not take effect in
any subsequent bar code commands. If any parameters are not specified, they take the default settings. The
last parameter must be the bar code data start identifier ("b" or "B") or the expanded character data start
identifier ("l" or "L"). Other parameters can be specified in any sequence. The prefix of each parameter can
be either a lower-case or upper-case character, - for example, "t0" or "T0", "s3" or "S3", etc.
3.1. Bar Code Mode
(All Model)
n = "t0" or "T0" CODE 39 (default)
n = "t1" or "T1" Interleaved 2 of 5
n = "t3" or "T3" FIM (US-Post Net)
n = "t4" or "T4" Post Net (US-Post Net)
n = "t5" or "T5" EAN 8, EAN 13, or UPC A
n = "t6" or "T6" UPC E
n = "t9" or "T9" Codabar
n = "t12" or "T12" Code 128 set A
n = "t13" or "T13" Code 128 set B
n = "t14" or "T14" Code 128 set C
n = "t130" or "T130" ISBN (EAN)
n = "t131" or "T131" ISBN (UPC-E)
n = "t132" or "T132" EAN 128 set A
n = "t133" or "T133" EAN 128 set B
n = "t134" or "T134" EAN 128 set C
(only HL-
L5000D/L5580D/L5100DN/L5200DW/L6200DW/L6300DW/L6400DW/L8250CDN/L8350CDW/L9200CDW
/L9300CDW)
n = "t137" or "T137" Code 93
n = "t138" or "T138" Code 93 Extend
n = "t139" or "T139" GS1 Databar Omnidirectional
n = "t140" or "T140" GS1 Databar Truncated
n = "t141" or "T141" GS1 Databar Stacked
n = "t142" or "T142" GS1 Databar Stacked Omnidirectional
n = "t143" or "T143" GS1 Databar Limited
n = "t144" or "T144" GS1 Databar Expanded
n = "t145" or "T145" GS1 Databar Expanded Stacked
n = "t146" or "T146" MSI
n = "t147" or "T147" MSI + CHK10
n = "t148" or "T148" MSI + CHK11_IBM
n = "t149" or "T149" MSI + CHK11_NCR
n = "t150" or "T150" MSI + CHK10 + CHK10
n = "t151" or "T151" MSI + CHK11_IBM + CHK10
n = "t152" or "T152" MSI + CHK11_NCR + CHK10
n = "t200" or "T200" PDF417
n = "t201" or " 201" Compact PDF417
n = "t202" or "T202" Macro PDF417
This parameter selects the bar code mode as above. When n is "t5" or "T5", the bar code mode (EAN 8, EAN
13, or UPC A) varies according to the number of characters in the data.
3.2. Bar Code Style, Expanded Character Shading, Line Block Drawing & Box
Drawing Shading
ï‚Ÿ Bar Code Style
n = "s0" or "S0" 3 : 1 (default)
To Next Page
Loading...
Need help?
General
Weight and Dimensions
