Brother ST531HD User Manual (English)

Questions and Answers:

C
christensenjeffreyAug 16, 2025
Why does my Brother ST531HD Sewing Machine needle keep breaking?
- R
  robert32Aug 16, 2025
  If your Brother Sewing Machine needle breaks, several factors could be at play. Ensure the needle is correctly installed and that the needle clamp screw is firmly tightened using a disc-shaped screwdriver. A bent or blunt needle should be replaced immediately. Also, check that the upper thread is correctly threaded, and you're using the right combination of fabric, thread, and needle. If the upper thread tension is too tight, loosen it. Make sure the spool is fitted properly and that you are using a bobbin designed for your machine. If the area around the hole in the needle plate or the presser foot is scratched, or if the bobbin case is scratched, contact your retailer or the nearest authorized service center.
J
Jeffrey PetersonAug 18, 2025
What to do if my Brother Sewing Machine is skipping stitches?
- O
  Oscar AllenAug 18, 2025
  If your Brother Sewing Machine stitches are skipped, make sure that the upper thread is correctly threaded and that you're using the right combination of fabric, thread, and needle. Replace the needle if it is bent or blunt, and ensure it is correctly installed. Also, remove the needle plate and clean any accumulated dust from the plate and the bobbin case.
J
jonathanthompsonAug 22, 2025
Why is my Brother ST531HD not working?
- T
  tayloryolandaAug 22, 2025
  If your Brother Sewing Machine is not working, first ensure that the main power switch is turned on. Check that the bobbin winder shaft is moved to the left. Also, make sure you are using the foot controller properly.
M
Michael FrenchAug 25, 2025
Why is my Brother Sewing Machine not feeding fabric?
- G
  Glen EstradaAug 26, 2025
  If the fabric does not feed through your Brother Sewing Machine, try lengthening the stitch length. Ensure the feed dogs are raised by sliding the feed dog position switch. Verify that you are using the right combination of fabric, thread, and needle. Also, remove any tangled thread, cleaning the race if necessary.
D
Drew SmithAug 28, 2025
Why does my Brother ST531HD Sewing Machine make a rattling noise?
- J
  jennifercarterAug 28, 2025
  If a high-pitched sound or rattling noise is produced while sewing with your Brother Sewing Machine, clean the bobbin case. This may be due to dust accumulation in the feed dogs or bobbin case.
K
Kristine KeithAug 31, 2025
Why does the upper thread keep breaking on my Brother ST531HD?
- C
  chanhaleyAug 31, 2025
  If the upper thread of your Brother Sewing Machine breaks, make sure that you have threaded the upper thread properly, ensuring the spool is correctly fitted and the thread is properly guided. Check that the needle is appropriate for the thread you are using. If the upper thread tension is too tight, loosen it.
S
Samantha WilsonSep 2, 2025
What to do if the lower thread is tangled in my Brother ST531HD?
- L
  Lisa JacobsSep 3, 2025
  If the lower thread of your Brother Sewing Machine is tangled or breaks, ensure that you have wound the bobbin thread properly. Remove any tangled thread and clean the race. Use a bobbin that has been designed for this machine and reset the bobbin thread correctly.
K
Kelly NortonSep 5, 2025
Why is the stitch not sewn correctly on my Brother ST531HD?
- M
  Michael GoldenSep 6, 2025
  If the stitch is not sewn correctly on your Brother Sewing Machine, attach the presser foot that is correct for the type of stitch that you want to sew. Adjust the tension of the upper thread. Remove any tangled thread, and if the thread is tangled in the bobbin case, clean the bobbin case.
D
Devin GriffithSep 9, 2025
Why is the fabric wrinkling when I sew with my Brother ST531HD?
- E
  Emma EdwardsSep 9, 2025
  If the fabric is wrinkled when using your Brother Sewing Machine, ensure that the upper thread is threaded properly, and the bobbin is correctly wound and fitted. Also, make sure the spool is fitted properly and that you're using the right combination of fabric, thread, and needle. When sewing thin fabrics, use a stabilizer material under the fabric and shorten the stitch length.
G
Gregory HesterSep 12, 2025
What to do if fabric is stuck in my Brother Sewing Machine?
- R
  robinsonkatrinaSep 12, 2025
  If the fabric cannot be removed from your Brother Sewing Machine, lift up the fabric and cut the threads below it. Then, clean the race.