To Next PageTo Next PageHow to fix BROVIND CFV12A Controller when the display doesn't light up?
First, check that the power cable is properly connected to the mains. Next, open the controller box and ensure the power is correctly connected inside. Also, inspect the fuses on the board to see if they are in good condition. Finally, use a testing device to verify that power is reaching the switch on the controller box.
What to do if BROVIND Controller shows a short-circuit at output?
Turn off the controller immediately and inspect the output for any short-circuits. If no shorts are found, attempt to turn the controller back on. Additionally, check if the vibrator speed was accidentally set to 0 for safety reasons (A0) and reset it.
Why is the vibrator not working on my BROVIND CFV12A Controller?
Make sure that all parameters are set correctly, including vibration amplitude, frequency, and the activation/deactivation of sensors. Also, verify that the vibrator is properly connected to the power board.
What does Supply voltage alarm mean on BROVIND Controller?
The supply voltage alarm activates if the supply voltage falls below 50 Volts or exceeds 300 Volts.
What to do if BROVIND Controller is stopped by a sensor?
Go to the menu for sensor 1 and/or sensor 2 and disable the sensor that is causing the issue.
How to reset BROVIND CFV12A Controller parameters to factory settings?
The factory-set parameters can be restored by selecting configuration 5 in the “Saving Work Configurations” menu (Menu 40).
What does SRV02 probe alarm mean on BROVIND CFV12A Controller?
This alarm indicates that the probe is set but is not responding. It activates if, with A0 greater than 1.0, As stays at 0 for at least 20 seconds.
Essential safety precautions to be followed before and during controller operation and maintenance.
Step-by-step guide for physically installing the controller, including connections.
Wiring diagram for the terminal board of CFF and CFV controller models.
Wiring diagram for the terminal board of the DCFF controller model.
Wiring diagrams for CFF15A and CFF10A 400V controller terminal boards.
Explanation of error codes (E00-E05) and message codes displayed by the controller.
Configuring the Balance Function for automatic weighing systems.
Configuration steps for the Elevator Unit function on DCFF controllers.
Details on configuring the Discharge Unit function for DCFF controllers.
Using controllers to program logic functions for inputs and outputs.
Instructions on using the 3-button keyboard to navigate menus and set parameters.
Procedure for automatically calibrating the vibrator for optimal performance.
Detailed steps to perform automatic calibration, including setting maximum values.
Creating, changing, and enabling logic blocks for custom program sequences.
Enabling S3 sensor, antiblock function, and activating programs.
Explains Open Loop and Closed Loop control modes with and without SRV02 probe.
Guidelines for controller maintenance, replacement, and basic troubleshooting.
Steps to take if the display does not light up or the vibrator does not work.
Essential safety precautions to be followed before and during controller operation and maintenance.
Step-by-step guide for physically installing the controller, including connections.
Wiring diagram for the terminal board of CFF and CFV controller models.
Wiring diagram for the terminal board of the DCFF controller model.
Wiring diagrams for CFF15A and CFF10A 400V controller terminal boards.
Explanation of error codes (E00-E05) and message codes displayed by the controller.
Configuring the Balance Function for automatic weighing systems.
Configuration steps for the Elevator Unit function on DCFF controllers.
Details on configuring the Discharge Unit function for DCFF controllers.
Using controllers to program logic functions for inputs and outputs.
Instructions on using the 3-button keyboard to navigate menus and set parameters.
Procedure for automatically calibrating the vibrator for optimal performance.
Detailed steps to perform automatic calibration, including setting maximum values.
Creating, changing, and enabling logic blocks for custom program sequences.
Enabling S3 sensor, antiblock function, and activating programs.
Explains Open Loop and Closed Loop control modes with and without SRV02 probe.
Guidelines for controller maintenance, replacement, and basic troubleshooting.
Steps to take if the display does not light up or the vibrator does not work.
General| Brand | BROVIND |
|---|---|
| Model | CFV12A |
| Category | Controller |
| Language | English |
