Bryant BH16NA - User Manual

To Next Page

BH14NB, BH16NA

Single-- Stage Split System Heat Pump

with Puronr Refrigerant

1–1/2 To 5 Nominal Tons

Installation Instructions

NOTE: Read the entire instruction manual before starting the

installation.

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service, maintenance,

or use can cause explosion, fire, electrical shock, or other

conditions which may cause death, personal injury, or property

damage. Consult a qualified installer, service agency, or your

distributor or branch for information o r assistance. The qualified

installer or agency must use factory–authorized kits or accessories

when modifying this product. Refer to the individual instructions

packaged with the kits or accessories when installing.

Follow all safety codes. Wear safety glasses, protective clothing,

and work gloves. Use quenching cloth for brazing operations.

Have fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions included in

literature and attached to the unit. Consult local building codes and

current editions of the National Electrical Code (NEC) NFPA 70.

In Canada, refer to current editions of the Canadian electrical code

CSA 22.1.

Recognize safety information. This is the safety–alert symbol

When you see this symbol on the unit and in instructions or

manuals, be alert to the potential for personal injury.

Understand these signal words; DANGER, WARNING, and

CAUTION. These words are used with the safety–alert symbol.

DANGER identifies the mo st serious hazards which will result in

severe personal injury or death. WARNING signifies hazards

which could result in personal injury or death. CAUTION is used

to identify unsafe practices which may result in minor personal

injury or product and property damage. NOTE is used to highlight

suggestions which will result in enhanced installation, reliability, or

operation.

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury

or death.

Before installing, modifying, or servicing system, main

electrical disconnect switch must be in the OFF position.

There may be more than 1 disconnect switch. Lock out and

tag switch with a suitable warning label.

EXPLOSION HAZARD

Failure to follow this warning could

result in death, serious personal injury,

and/or property damage.

Never use air or gases containing

oxygen for leak testing or operating

refrigerant compressors. Pressurized

mixtures of air or gases containing

oxygen can lead to an explosion.

WARNING

INSTALLATION RECOMMENDATIONS

NOTE: In some cases noise in the living area has been traced to

gas pulsations from improper installation of equipment.

1. Locate unit away from windows, patios, decks, etc. where

unit operation sound may disturb customer.

2. Ensure that vapor and liquid tube diameters are appropriate

for unit capacity.

3. Run refrigerant tubes as directly as possible b y avoiding un-

necessary turns and bends.

4. Leave some slack between structure and unit to absorb vi-

bration.

5. When passing refrigerant tubes through the wall, seal open-

ing with RTV or other pliable silicon–based caulk (see Fig.

1).

6. Avoid direct tubing contact with water pipes, duct work,

floor joists, wall studs, floors, and walls.

7. Do not suspend refrigerant tubing from joists and studs with

a rigid wire or strap which comes in direct contact with

tubing (see Fig. 1).

8. Ensure that tubing insulation is pliable and completely sur-

rounds vapor tube.

9. When necessary, use hanger straps which are 1 in. wide and

conform to shape of tubing insulation (see Fig. 1).

10. Isolate hanger straps from insulation by using metal sleeves

bent to conform to shape of insulation.

INSULATION

SUCTION TUBE

LIQUID TUBE

OUTDOOR WALL INDOOR WALL

LIQUID TUBE

SUCTION TUBE

INSULATION

CAULK

HANGER STRAP

(AROUND SUCTION

TUBE ONLY)

JOIST

1” (25.4 mm)

MIN

THROUGH THE WALL

SUSPENSION

A07588

Fig. 1 – Connecting Tubing Installation

When outdoor unit is connected to factory–approved indoor unit,

outdoor unit contains system refrigerant charge for operation with

AHRI rated indoor unit when connected by 15 ft. (4.57 m) of

field–supplied or factory accessory tubing. For proper unit

operation, check refrigerant charge using charging information

located on control box cover and/or in the Check Charge section of

this instruction.

IMPORTANT: Maximum liquid–line size is 3/8–in. OD for all

residential applications including long line.

IMPORTANT: Always install the factory–supplied liquid–line

filter drier . Obtain replacement filter driers from your distributor or

branch.

Main Page

Need help?

Do you have a question about the Bryant BH16NA and is the answer not in the manual?

Summary

Installation Instructions and Safety

Comprehensive Safety Considerations

Detailed safety precautions, warnings for electrical shock and explosion hazards during installation.

Job Site and Unit Preparation

Hazard Warnings and Site Prep

Safety cautions for hazards like cuts and unit damage, plus preparing the installation site.

Piping and Service Valve Procedures

Personal and Environmental Safety

Warnings regarding personal injury, environmental hazards, and refrigerant handling during service.

Brazing and Filter Drier Installation

Brazing Safety and Procedures

Guidelines for safe brazing techniques, using appropriate materials, and fire hazard prevention.

System Evacuation and Electrical Connections

Refrigerant System Evacuation

Procedure for deep vacuum evacuation of refrigerant tubing and indoor coil to remove moisture and air.

Electrical Connection Safety

Critical safety warnings for making electrical connections, emphasizing grounding.

Wiring and Start-Up Procedures

System Start-Up Safety

Crucial safety precautions to follow before and during system start-up to prevent injury or damage.

Summary

Installation Instructions and Safety

Comprehensive Safety Considerations

Detailed safety precautions, warnings for electrical shock and explosion hazards during installation.

Job Site and Unit Preparation

Hazard Warnings and Site Prep

Safety cautions for hazards like cuts and unit damage, plus preparing the installation site.

Piping and Service Valve Procedures

Personal and Environmental Safety

Warnings regarding personal injury, environmental hazards, and refrigerant handling during service.

Brazing and Filter Drier Installation

Brazing Safety and Procedures

Guidelines for safe brazing techniques, using appropriate materials, and fire hazard prevention.

System Evacuation and Electrical Connections

Refrigerant System Evacuation

Procedure for deep vacuum evacuation of refrigerant tubing and indoor coil to remove moisture and air.

Electrical Connection Safety

Critical safety warnings for making electrical connections, emphasizing grounding.

Wiring and Start-Up Procedures

System Start-Up Safety

Crucial safety precautions to follow before and during system start-up to prevent injury or damage.

This document describes the installation and maintenance of Bryant BH14NB and BH16NA Single-Stage Split System Heat Pumps with Puron® Refrigerant, ranging from 1-1/2 to 5 nominal tons.

Function Description:

The Bryant BH14NB and BH16NA are single-stage split system heat pumps designed for residential heating and cooling applications. They utilize Puron® refrigerant (R-410A) and are intended for connection to factory-approved indoor units. The system includes an outdoor unit, an indoor unit (such as a fan coil or furnace), and refrigerant tubing to connect them. The heat pump operates in both cooling and heating modes, with a defrost control system to manage frost accumulation on the outdoor coil during heating.

Important Technical Specifications:

Nominal Tonnage: 1-1/2 to 5 nominal tons.
Refrigerant: Puron® (R-410A). Puron refrigerant operates at 50-70 percent higher pressures than R-22.
Refrigerant Cylinders: Rose colored, with a service pressure rating of 400 psig (DOT 4BA400 or DOT BW400).
Manifold Sets: Required to be 700 psig high side and 180 psig low side with 550 psig low-side retard.
Hoses: Must have a 700 psig service pressure rating.
Filter Driers: Factory-supplied liquid-line filter drier is required on every unit. Do not use liquid-line filter driers with rated working pressures less than 600 psig. Suction-line filter driers should not be installed in the liquid line or left in line longer than 72 hours.
Piston Metering Device: Units with indoor pistons require a specific piston size, which must match the unit rating plate. If equipped with an R-22 TXV or piston metering device sized for R-22, it must be changed to a hard shutoff Puron TXV.
Outdoor Operating Ambient: Minimum 55°F (12.78°C) in cooling mode (without accessory), maximum 125°F (51.67°C) in cooling mode. Maximum 66°F (18.89°C) in heating mode.
Tubing Lengths: Factory charged for 15 ft (4.57 m) of lineset. For lengths between 80 and 200 ft (24.38 and 60.96 m) horizontally or 20 ft (6.09 m) vertically, refer to the Residential Piping and Longline Guideline.
Liquid-Line Size: Maximum 3/8-in. OD for all residential applications, including long line.
Electrical Wiring: No. 18 AWG color-coded, insulated (35°C minimum) wire for control wiring. For runs over 100 ft (30.5 m), use No. 16 AWG. All wiring must be NEC Class 2 and separated from incoming power leads.
Transformer: Furnace, fan coil, or accessory transformer for control power, 24v/40va minimum.
Clearances: 24 in. (609.6 mm) to service end, 48 in. (1219.2 mm) above unit. 6 in. (152.4 mm) on one side, 12 in. (304.8 mm) on all remaining sides. 18 in. (457.2 mm) for units with wire grille coil guard; 24 in. (609.6 mm) for units with louver panels. Unit must be at least 6 in. above roof surface for rooftop applications.
Defrost Control: Time/temperature control with field-selectable time periods (30, 60, or 90 minutes), factory set to 60 or 90 minutes.

Usage Features:

Installation Location: Locate unit away from windows, patios, and decks to minimize noise disturbance.
Mounting: Install on a solid, level mounting pad, ensuring it is level to within ±2° (±3/8 in/ft, ±9.5 mm/m). For rooftop applications, mount on a level platform or frame, above a load-bearing wall, and at least 6 inches above the roof surface.
Refrigerant Tubing: Run as directly as possible, avoiding unnecessary turns and bends. Leave slack for vibration absorption. Seal wall openings with RTV or pliable silicon-based caulk. Avoid direct contact with water pipes, duct work, floor joists, wall studs, floors, and walls. Use 1-inch wide hanger straps conforming to insulation shape, isolated from insulation by metal sleeves.
Brazing: Use Sil-Fos or Phos-copper alloy. Wrap service valves with a wet cloth or heat-sinking material to prevent overheating and damage. Remove valve cores from Schrader ports on service valves before brazing.
Evacuation: Evacuate refrigerant tubes and indoor coil to 500 microns using the deep vacuum method. Never use the system compressor as a vacuum pump.
Charging: Units are factory charged for 15 ft of lineset. Adjust charge by adding or removing 0.6 oz/ft (0.018 kg/m) of 3/8 liquid line above or below 15 ft. For TXV systems, use the subcooling method. For piston systems, use the superheat method. Favorable conditions for charging exist when outdoor temperature is 70-100°F (21.11-37.78°C) and indoor temperature is 70-80°F (21.11-26.67°C).
Electrical Connections: Ensure field wiring complies with local and national codes. Connect ground wire to the control box. Route 24v control wires through the grommet and connect leads to control wiring.
Crankcase Heater: If equipped, furnish power to the heater a minimum of 24 hours before starting the unit, especially if tubing is longer than 80 ft (24.38 m) or the outdoor unit is 20 ft (6.10 m) below the indoor unit.
Start-Up: After evacuation, fully open liquid and vapor service valves. Replace stem caps after opening to refrigerant flow. Close electrical disconnects to energize the system. Set the thermostat to desired temperature and mode (HEAT or COOL, ON or AUTO fan) and operate for 15 minutes.

Maintenance Features:

Periodic Maintenance: Regular maintenance is required for continuing high performance and minimizing equipment failure. Frequency may vary based on geographic areas (e.g., coastal applications). Refer to the User's Manual for detailed information.
Final Checks (Post-Installation):
- Ensure all wiring is routed away from tubing and sheet metal edges to prevent rub-through or pinching.
- Verify all wiring and tubing are secure in the unit before adding panels and covers.
- Tighten service valve stem caps to 1/12-turn past finger tight.
- Leave the Owner's Manual with the owner and explain system operation and periodic maintenance requirements.
- Fill out the Dealer Installation Checklist and place it in the customer file.
Refrigerant Recovery: Federal regulations require refrigerant recovery during system repair or final unit disposal. Never vent refrigerant to the atmosphere.
System Opening: When the system must be opened for service, recover refrigerant, evacuate, then break the vacuum with dry nitrogen, and replace filter driers. Evacuate to 500 microns prior to recharging.
POE Oils: POE oils absorb moisture rapidly and can damage certain plastics and roofing materials. Do not expose oil to the atmosphere.
Defrost Thermostat Check: Ensure the defrost thermostat is properly located and securely attached to the stub tube on the liquid header.
Filter Drier Replacement: Obtain replacement filter driers from your distributor or branch.

Bryant BH16NA Specifications

General

Type	Heat Pump
SEER Rating	Up to 16
HSPF Rating	Up to 9.5
Refrigerant	R-410A
Voltage	208/230
Phase	1
Compressor Type	Single Stage
Warranty	10 Years Limited Parts Warranty
Cooling Capacity (BTU/h)	18000
Heating Capacity (BTU/h)	18, 000