UK Declaration of Conformity | 16
Instruction Manual FOSSA FO 0015 A - FO 0035 B_EN_en 37 | 40
16 UK Declaration of Conformity
This Declaration of Conformity and the UKCA-markings affixed to the nameplate are valid for the machine within the Busch scope of delivery. This Dec-
laration of Conformity is issued under the sole responsibility of the manufacturer.
When this machine is integrated into a superordinate machinery the manufacturer of the superordinate machinery (this can be the operating compa-
ny, too) must conduct the conformity assessment process for the superordinate machine or plant, issue the Declaration of Conformity for it and affix
the UKCA-marking.
The manufacturer Ateliers Busch S.A.
Zone Industrielle
CH-2906 Chevenez
declares that the machine: FOSSA FO 0015 A; FOSSA FO 0035 B
with the serial number:
fulfill(s) all the relevant provisions from UK legislations:
– Supply of Machinery (Safety) Regulations 2008
– The Equipment and Protective Systems Intended for Use in Potentially Explosive Atmospheres Regulations 2016
– Electromagnetic Compatibility Regulations 2016
– Restriction of the use of certain hazardous substances in Electrical and Electronic Equipment Regulations 2021
and comply(-ies) with the following designated standards that have been used to fulfill those provisions:
Standards Title of the Standard
EN ISO 12100 : 2010 Safety of machinery - Basic concepts, general principles of design
EN ISO 13857 : 2019 Safety of machinery - Safety distances to prevent hazard zones being reached by the upper and lower
limbs
EN 1012-2 : 1996 + A1 : 2009 Vacuum pumps - Safety requirements - Part 2
EN ISO 2151 : 2008 Acoustics - Noise test code for compressors and vacuum pumps - Engineering method (grade 2)
CFR 47 FCC Part 15;
Class A (industry)
The FCC 47 CFR Part 15 from the Federal Communications Commission: rules and regulations for
EMC.
EN 60204-1 : 2018 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
ICES-001 Industrial scientific and medical (ism) radio frequency generators
EN IEC 61000-6-2 : 2019 Electromagnetic compatibility (EMC) - Generic standards. Immunity for industrial environments
EN IEC 61000-6-4 : 2019 Electromagnetic compatibility (EMC) - Generic standards. Emission standard for industrial environ-
ments
EN 61326-1 : 2013 Table 2 Electrical equipment for measurement, control and laboratory use. EMC requirements. General re-
quirements
EN 61000-3-2 : 2019
Class A (industry)
Electromagnetic compatibility (EMC) – Part 3-2: Limits – Limits for harmonic current emissions (equip-
ment input current ≤ 16 A per phase)
EN 61000-3-3 : 2013 + A1 : 2019 Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage fluctua-
tions and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per
phase and not subject to conditional connection.
EN 61010-1 : 2010 + A1 : 2019
+ A1 : 2019 / AC : 2019
Safety requirements for electrical equipment for measurement, control, and laboratory use. General
requirements
EN ISO 80079-36 : 2016 Explosive atmospheres - Part 36: Non-electrical equipment for explosive atmospheres - Basic method
and requirements
EN ISO 80079-37 : 2016 Explosive atmospheres - Part 37: Non-electrical equipment for explosive atmospheres - Non electrical
type of protection constructional safety ‘c’, control of ignition source ‘b’, liquid immersion ‘k’
EN 1127-1 : 2019 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodolo-
gy
Legal person authorized to compile the technical file
and importer in the UK
(if the manufacturer is not located in the UK):
Busch (UK) Ltd
30 Hortonwood
Telford - UK
Chevenez, 25.01.2022
Christian Hoffmann, General Director
To Next Page