What to do if BWT Rondomat Duo-DVGW 3 displays low salt?
If your BWT Water Dispenser displays a low salt warning, it means the regenerative wasn't refilled in time. To resolve this, siphon off or extract the brine to the level of the sieve base before refilling the regenerative. Incorrect refilling can cause the softened water to become salty.
What does Service! mean on my BWT Rondomat Duo-DVGW 3?
If your BWT Water Dispenser displays 'Service!', it means that maintenance is required after every 500 regenerations.
What to do if my BWT Water Dispenser shows 'Service!'?
If your BWT Water Dispenser displays 'Service!', this indicates that maintenance is required after every 500 regenerations. In this case, you should contact the after sales service.
What to do if my BWT Water Dispenser display indicates low salt (low salt! date time)?
If your BWT Water Dispenser display indicates low salt (low salt! date time), it means the regenerative was not refilled in time. The brine must be siphoned off or extracted to the level of the sieve base. Only after this has been done can the regenerative be refilled. If this is done incorrectly, the softened water will be salty.
Why is my BWT Rondomat Duo-DVGW 3 Water Dispenser not supplying enough water?
If your BWT Water Dispenser isn't providing sufficient water or the flow is weak, the inlet pressure might be too low, or the compressed air pressure could be insufficient. Try increasing the inlet pressure, adjusting the pressure reducer if needed, and start a manual regeneration. Also, check the inlet pressure and initiate regeneration.
How to fix BWT Rondomat Duo-DVGW 3 Water Dispenser not supplying softened water?
If your BWT Water Dispenser isn't supplying softened or blended water, it could be due to a lack of regenerative in the salt/brine container or a power supply interruption. Refill the regenerative, wait approximately one hour, and then manually regenerate the system. Also, ensure the electrical connection is properly re-established.
What does it mean when my BWT Water Dispenser displays 'Valve defective'?
If your BWT Water Dispenser displays a message indicating that Valve 1, 2, 3, or 4 is defective, the cable to the valve block might be faulty. Check the cable to the valve block and press OK to confirm.
What does 'Elyse' mean on my BWT Rondomat Duo-DVGW 3 display?
If your BWT Water Dispenser displays 'Elyse', it indicates an electrolysis cell overcurrent. Check the cable to the valve block for short circuits and press OK to confirm.
What does it mean when my BWT Water Dispenser display indicates 'Elyse'?
If your BWT Water Dispenser displays 'Elyse', it indicates an electrolysis cell overcurrent. Check the cable to the valve block for short circuits and press OK to confirm. If the malfunction persists, contact the after-sales service staff.
How to fix a BWT Water Dispenser that isn't supplying softened water?
If your BWT Water Dispenser is not supplying softened or blended water, it might be due to no regenerative in the salt/brine container or a power supply cut off. Refill the regenerative, wait approximately 1 hour, and then regenerate manually. Also, re-establish the electrical connection.
Important safety guidelines for installation and operation.
Guidelines for using treated water for plants and aquatic life.
Regular checks and correction of water hardness.
Lists the components included in the softening unit package.
Explanation of different product model identifiers.
Explains the ion exchange principle and operational method.
Details the disinfection device specific to DVGW models.
Describes the extended refill intervals for Duo-I BOB models.
Requirement to flush pipelines before unit installation.
Specifies water quality requirements for the unit's input.
Discusses the impact of chlorine on ion exchange resin.
Guidance on sizing the unit for adequate regeneration frequency.
Recommendations for selecting pipe materials for installation.
Importance and placement of a protective filter upstream.
Criteria for selecting an appropriate installation location.
Specifies requirements for mains power and operating pressure.
Requirement for a safety device like a hydrostop.
Environmental protection requirements for the installation site.
Ambient temperature limits for human consumption water.
Instructions for routing overflow and flushing water hoses.
Steps for installation performed by the user.
Specific installation instructions for units 6 and 10.
How to prepare the disinfectant solution for filling.
Table detailing filling quantities for different models.
Cleaning steps for column parts during installation.
Greasing O-rings and attaching the control valve and adapter.
Mounting the Soft-Control controller onto the plate.
Connecting the unit to the main water supply.
Connecting the brine hose to the unit.
Connecting the flushing water hose to the unit.
Connecting the overflow hose to the brine container.
Important notes on hose routing and connection to sewage.
Instructions for making electrical connections to the unit.
Wiring diagram for Rondomat Duo DVGW 2 and 3 models.
Wiring diagram for Industrial Rondomat Duo 2, 3, 6, 10 models.
Instruction to remove the mains plug before proceeding.
Mounting the DVGW electrolysis unit to the console.
Connecting wire A to the valve block and electrolysis cell.
Connecting wire B to the Soft Control controller terminals.
Alternative method for connecting the mains plug.
Details for the dosing output connection.
How to initiate the regeneration process.
Information on the regeneration signal output.
Functionality and connection of an optional pressure switch.
Explanation of the main operation screen elements.
Explanation of the selection screen and its options.
Verification step before starting the unit.
Waiting period for units 6 and 10 after filling disinfectant.
Initial power and water connection steps for startup.
How to cancel an ongoing regeneration cycle.
Procedure for setting the unit's time and date.
How to change the display language of the unit.
Initiating regeneration, column change, and quick flushing procedures.
Guide to selecting the display language.
Procedure for rinsing fine resin particles from the column.
Detailed steps for quick flushing the first softening column.
Steps involved in changing the softening column.
Detailed steps for quick flushing the second softening column.
Specific flushing instructions for Rondomat 6 and 10 models.
Warning not to alter the blended water hardness setting.
Setting the hardness of the incoming untreated water.
Setting the desired hardness of the softened blended water.
Information on automatic saving of changed values.
How to manually initiate a regeneration cycle.
Time required for brine formation after filling.
Manual water refilling process for Duo 2 and 3 models.
Information on sodium limits in drinking water regulations.
Method to calculate sodium increase from water softening.
Steps for final handover and user training of the unit.
How and when to refill the regenerative salt in the container.
How to manually initiate a regeneration cycle.
Overview of operator checks for warranty and proper functioning.
Detailed list of regular checks the operator must perform.
Schedule and tasks for annual unit servicing and replacement parts.
Conditions that will void the product warranty.
Exclusions from the 2-year legal warranty related to wear parts.
BWT's liability limitations for unit failures or capacity issues.
Impact of using non-compliant regenerative material on the warranty.
Troubleshooting steps for no softened or blended water supply.
Troubleshooting steps for insufficient water flow.
Interpreting and resolving the "low salt" display error.
Troubleshooting valve defects indicated by the display error.
Troubleshooting the "Elyse" error indication, likely electrolysis related.
General technical specifications for the Rondomat Duo series.
Technical specifications specific to Rondomat Duo DVGW models.
Technical specifications specific to Rondomat Duo I models.
Technical specifications specific to Rondomat Duo I BOB models.
Table detailing physical dimensions for Rondomat Duo models.
Diagram illustrating physical dimensions for Rondomat Duo 6/10 BOB.
Contact details for various BWT international offices.
General| Brand | BWT |
|---|---|
| Model | Rondomat Duo-DVGW 3 |
| Category | Water Dispenser |
| Language | English |
To Next Page