To Next PageTo Next PageWhat to do if BWT Rondomat Duo-I 6 Water Dispenser displays low salt?
If your BWT Water Dispenser displays a low salt warning, it means the regenerative wasn't refilled in time. To resolve this, siphon off or extract the brine to the level of the sieve base before refilling the regenerative. Incorrect refilling can cause the softened water to become salty.
What does Service! mean on my BWT Rondomat Duo-I 6?
If your BWT Water Dispenser displays 'Service!', it means that maintenance is required after every 500 regenerations.
What to do if my BWT Water Dispenser shows 'Service!'?
If your BWT Water Dispenser displays 'Service!', this indicates that maintenance is required after every 500 regenerations. In this case, you should contact the after sales service.
What to do if my BWT Water Dispenser display indicates low salt (low salt! date time)?
If your BWT Water Dispenser display indicates low salt (low salt! date time), it means the regenerative was not refilled in time. The brine must be siphoned off or extracted to the level of the sieve base. Only after this has been done can the regenerative be refilled. If this is done incorrectly, the softened water will be salty.
Why is my BWT Rondomat Duo-I 6 Water Dispenser not supplying enough water?
If your BWT Water Dispenser isn't providing sufficient water or the flow is weak, the inlet pressure might be too low, or the compressed air pressure could be insufficient. Try increasing the inlet pressure, adjusting the pressure reducer if needed, and start a manual regeneration. Also, check the inlet pressure and initiate regeneration.
How to fix BWT Water Dispenser not supplying softened water?
If your BWT Water Dispenser isn't supplying softened or blended water, it could be due to a lack of regenerative in the salt/brine container or a power supply interruption. Refill the regenerative, wait approximately one hour, and then manually regenerate the system. Also, ensure the electrical connection is properly re-established.
What does it mean when my BWT Rondomat Duo-I 6 Water Dispenser displays 'Valve defective'?
If your BWT Water Dispenser displays a message indicating that Valve 1, 2, 3, or 4 is defective, the cable to the valve block might be faulty. Check the cable to the valve block and press OK to confirm.
What does 'Elyse' mean on my BWT Rondomat Duo-I 6 display?
If your BWT Water Dispenser displays 'Elyse', it indicates an electrolysis cell overcurrent. Check the cable to the valve block for short circuits and press OK to confirm.
What does it mean when my BWT Water Dispenser display indicates 'Elyse'?
If your BWT Water Dispenser displays 'Elyse', it indicates an electrolysis cell overcurrent. Check the cable to the valve block for short circuits and press OK to confirm. If the malfunction persists, contact the after-sales service staff.
How to fix a BWT Water Dispenser that isn't supplying softened water?
If your BWT Water Dispenser is not supplying softened or blended water, it might be due to no regenerative in the salt/brine container or a power supply cut off. Refill the regenerative, wait approximately 1 hour, and then regenerate manually. Also, re-establish the electrical connection.
General| Brand | BWT |
|---|---|
| Model | Rondomat Duo-I 6 |
| Category | Water Dispenser |
| Language | English |
General guidance and cautions for safe operation.
Specifies required water quality, pipe materials, and flushing procedures.
Details site protection against frost, chemicals, and temperature limits.
Outlines requirements for sewage connections, floor drains, and hose routing.
Steps for mounting and connecting the electronic controller unit.
Instructions for connecting the unit to water supply and drainage systems.
Instructions for adding salt to the brine container.
Lists routine checks the operator must perform for optimal function.
Specific checks to ensure proper unit function.
Schedule for replacing parts and performing servicing.
Conditions that will void the product warranty.
Common issue and its cause/action for no water supply.
Troubleshooting steps for low water flow.
Interpreting and resolving the 'low salt' display message.
