Cafe CDT845P4NW2 - User Manual

READ CAREFULLY
KEEP THESE INSTRUCTIONS
31-4000216 Rev 2 10-20 GEA
CHECK THE FOLLOWING
 Tub trim does not interfere with the door
 Dishwasher is square and level at both the top and bottom of the cabinet opening,
with no twisting or distortion of the tub or door
 All 4 legs of the dishwasher are firmly in contact with the floor
 Drain hose is not pinched between the dishwasher and adjacent cabinets or walls
 Tub trim is fully seated on the tub flange
Printed in the United States
TM
WARNING
CAUTION
FOR YOUR SAFETY
Read and observe all WARNINGS and CAUTIONS
shown throughout these instructions.
IMPORTANT – Observe all governing codes and
ordinances.
• Note to Installer – Be sure to leave these instructions
for the consumer’s and local inspector’s use.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills. Proper
installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliances Warranty. See
Warranty information.
• Completion Time – 1 to 3 Hours. New installations
require more time than replacement installations.
IMPORTANT – The dishwasher MUST be installed to
allow for future removal from the enclosure if service is
required.
Care should be exercised when the appliance is
installed or removed, to reduce the likelihood of
damage to the power supply cord.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for
available custom panel kits.
Your dishwasher is a water heating appliance.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• To reduce the risk of electric shock, fire, or injury to
persons, the installer must ensure that the dishwasher is
completely enclosed at the time of installation.
• FOR PERSONAL SAFETY: Remove house fuse or open
circuit breaker before beginning installation. Do not use
an extension cord or adapter plug with this appliance.
• The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative if
you are in doubt that the appliance is properly grounded.
• If house wiring is not 2-wire with ground, a ground
must be provided by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.
• To reduce the risk of electric shock, fire, or injury to
persons, the installer should check to ensure that wires
are not pinched or damaged, the house wiring is attached
to the junction box bracket through a strain relief, and
all electrical connections made at the time of install (wire
nuts) are contained inside of the junction box cover.
Do not remove wood base until you are ready to install
the dishwasher. The dishwasher will tip over when the
door is opened if base is removed.
While performing installations described in this booklet,
gloves, safety glasses or goggles should be worn.
If you have questions, visit our website at: cafeappliances.com.
In Canada, visit: cafeappliances.ca
Built-In Dishwashers
Installation
Instructions

Summary

Installation Overview and Safety

Before You Begin

Read installation instructions completely and carefully before proceeding with setup.

Safety Precautions

Review all WARNINGS and CAUTIONS, including electrical shock, fire, and injury risks.

Pre-Installation Checklist

Verify specific conditions before installation, such as tub trim, leveling, and drain hose placement.

Installation Preparation: Parts and Materials

Parts Supplied

List of components included in the installation package for the dishwasher.

Required Materials

List of materials and supplies needed for dishwasher installation.

Tools Required

List of tools necessary for completing the dishwasher installation.

Installation Preparation: Enclosure and Drains

Prepare Dishwasher Enclosure

Ensure the cabinet opening meets specific dimensions and is free of obstructions for installation.

Drain Requirements

Follow local codes for drain installation, including air gap usage and maximum hose length.

Cabinet Preparation

Drill a 1-1/2" hole for the drain hose connection, ensuring smooth edges.

Installation Preparation: Electrical Wiring

Electrical Requirements

Ensure 120V, 60Hz, AC-only, 15- or 20-ampere fused electrical supply with proper wiring.

Grounding Instructions

Proper grounding is essential for safety; follow permanent connection or power cord model guidelines.

Cabinet Preparation & Wire Routing

Prepare cabinet for wiring, cutting holes and ensuring smooth edges for cable entry.

Electrical Connection

Connect electrical wiring to the dishwasher on the right front, following specified routing.

Installation Preparation: Water Line

Prepare Hot Water Line

Use recommended copper tubing or flexible hose for the water supply line connection.

Water Line Connection

Connect the water supply, install shut-off valve, and ensure proper water temperature and pressure.

Dishwasher Installation: Initial Steps

Step 1 Preparation: Locate Items

Gather all parts supplied in the installation package before proceeding.

Step 2 Check Door Balance

Verify the dishwasher door opens and closes smoothly and self-closes within 20 degrees.

Step 3 Remove Base and Install Leveling Legs

Remove the wood base and install the leveling legs, adjusting height as needed.

Dishwasher Installation: Unit Preparation and Connections

Prepare Unit Components

Remove toekick and manage floor protect pan as required for installation.

Install Water and Drain Connections

Connect 90° elbow, install drain hose loop, and position water/wiring lines.

Dishwasher Installation: Positioning and Trim

Slide Dishwasher into Cabinet

Carefully slide the dishwasher into the opening, managing utility lines and ensuring no kinks.

Install Trim Pieces

Attach the top and side trim pieces to the tub flange for a finished appearance.

Dishwasher Installation: Securing and Final Placement

Install Mounting Brackets

Secure mounting brackets to the tub frame for countertop or cabinet attachment.

Push Dishwasher into Final Position

Slide dishwasher fully into place, checking alignment and ensuring door panel is behind cabinet face.

Dishwasher Installation: Final Positioning and Leveling

Final Dishwasher Alignment Check

Ensure door operates smoothly, does not rub cabinets, and utility lines are not trapped.

Level Dishwasher

Level the dishwasher left-to-right and front-to-back for proper operation and rack stability.

Dishwasher Installation: Securing and Water Connection

Secure Dishwasher to Countertop or Cabinet

Fasten the dishwasher to the countertop or cabinet sides using provided screws.

Connect Water Supply

Connect the water supply line to the 90° elbow, ensuring proper compression fittings.

Dishwasher Installation: Drain Line Connection

Connect Drain Line to Inlet Port

Cut drain hose if needed and connect to air gap, waste tee, or disposer with clamp.

Drain Line Routing and Length

Ensure proper drain line routing, no kinks, and total length does not exceed 16 feet.

Dishwasher Installation: Power and Pre-Test

Connect Power Supply

Secure house wiring to junction box using strain relief and wire nuts, then install cover.

Pre-Test Checklist

Review final checks to avoid service calls, ensuring power is off and all connections are secure.

Dishwasher Installation: Testing and Insulation

Dishwasher Wet Test

Run a cycle to check water entry, leaks, and proper draining after installation.

Position Sound Insulation

Place sound insulation block under the control box for noise reduction, if equipped.

Dishwasher Installation: Final Checks and Literature

Replace Toekick

Reattach the toekick, ensuring it is aligned and in contact with the floor.

Final Checks

Verify tub trim, leveling, drain hose, and overall alignment for optimal performance.

Leave Literature for Consumer

Provide the consumer with installation instructions, manual, and product samples.

Cafe CDT845P4NW2 Specifications

General

Type	Built-In
Touch Buttons	Yes
Energy Star Certified	Yes
Stainless Steel Tub	Yes
Soil Sensor	Yes
Delay Start	Yes
Water Heater	Yes
Drying Option	Condensation drying