California Air Tools 10020AC

Questions and Answers

S
Sharon EstesAug 15, 2025
What to do if my California Air Tools 10020AC doesn't provide enough air?
- B
  Brittney SandersAug 15, 2025
  If your California Air Tools Air Compressor isn't providing as much air as it used to, or it cuts off sooner than expected, it could be due to two reasons. One reason might be that the tank is full of water from condensation. To fix this, open the drain valve and release the water from the tank. Another possible reason is that the pressure switch needs adjustment, in this case you should contact the dealer.
E
Emily RobertsonAug 18, 2025
Why won't my California Air Tools Air Compressor motor start or starts slowly?
- J
  Jesus MccoyAug 18, 2025
  If your California Air Tools Air Compressor motor doesn't start or starts slowly, it could be due to a low voltage supply to the motor. Ensure the main voltage matches the air compressor's specifications. Avoid thin or long extension cords, as they can cause voltage drops. Use heavy-duty extension cords and ensure the compressor is plugged into a fully functional power outlet.
C
Carolyn ChavezAug 22, 2025
What to do if my California Air Tools 10020AC Air Compressor stopped and does not start?
- J
  Jessica PrestonAug 22, 2025
  If your California Air Tools Air Compressor stops and doesn't restart, the thermal protector may have activated due to the motor overheating. Ensure the main voltage matches the air compressor's specifications. Avoid thin or long extension cords to prevent voltage drops. Excessive use (over 1 hour continuously) can also cause overheating, so allow the motor to cool down. If the motor windings are burned out, contact Customer Support.
M
Michael JenningsAug 26, 2025
What to do if California Air Tools Air Compressor motor pump unit does not stop at maximum pressure?
- J
  Judy MitchellAug 26, 2025
  If the motor pump unit of your California Air Tools Air Compressor doesn't stop when the tank pressure reaches its maximum working pressure (75 PSI), the pressure switch may be defective or need adjustment. Stop the compressor immediately and contact Customer Support.
V
Vanessa StricklandAug 28, 2025
How to fix a pressure drop in my California Air Tools 10020AC Air Compressor tank?
- S
  Shannon SmithAug 28, 2025
  If your California Air Tools Air Compressor has a pressure drop in the tank, it's likely due to air leaks at the connections. To identify the leaks, let the compressor build pressure, then brush soapy water on the air connections and watch for bubbles. Tighten any leaky connections. If the problem continues, contact the seller for further assistance.
K
Kathleen MendezAug 31, 2025
Why is my California Air Tools 10020AC Air Compressor so noisy?
- C
  christopherhernandezSep 1, 2025
  If your California Air Tools Air Compressor is noisy with metallic clangs, it could indicate a damaged compressor head gasket or reed valve. Stop the compressor immediately and contact the dealer for assistance.
T
Tiffany RiggsSep 4, 2025
What to do if my California Air Tools Air Compressor does not reach maximum pressure?
- J
  juansmithSep 4, 2025
  If your California Air Tools Air Compressor does not reach the maximum pressure, the compressor head gasket or reed valve may be faulty. Stop the compressor and contact the dealer.
S
Steven SmithSep 7, 2025
How to fix unloader valve leak in California Air Tools Air Compressor?
- C
  Cynthia HammondSep 7, 2025
  If the unloader valve on your California Air Tools Air Compressor leaks when the compressor is idle, it's likely that the unloader valve seal is defective. Release all the pressure from the air tank. Then, remove the unloader valve plug and clean the valve seal. If necessary, replace the seal and reinstall all components.
M
mackronaldSep 12, 2025
Why does my California Air Tools Air Compressor motor hum but not start?
- S
  Stephanie PerrySep 12, 2025
  If the motor of your California Air Tools Air Compressor doesn't start and makes a humming noise, the capacitor might be burned out. Contact Customer Support for assistance.

Summary

Important Safety Instructions

Locations of Important Labels

Air Compressor Components

Pre-Operation Checklist

Package Contents & Assembly

Lists included items and guides initial assembly of the compressor.

Inspect for Damage

Procedure for checking the air compressor for any damage before operation.

Save Packaging

Recommendation to keep original packaging for potential returns or service.

Compressor Location

Guidance on selecting a suitable and safe location for the air compressor.

Maintain a Clear Area

Importance of adequate ventilation and clearance around the compressor.

Use in Areas with Clean Air

Advice on operating the compressor in a dust-free environment for longevity.

Operating the Air Compressor

Introduction

Brief overview of the air compressor's features and benefits.

Assembly

Instructions for connecting the air supply hose and preparing for operation.

Test Run

Procedure for the initial startup and operational check of the compressor.

Daily Operation

Steps for starting, operating, and regulating the air compressor during normal use.

Shutting Down the Compressor

Steps for safely turning off and disconnecting the air compressor.

Maintenance

Draining the Air Tank

Procedure for removing moisture and preventing rust in the air tank.

Cleaning or Changing the Air Filter

Instructions for maintaining the air filter for optimal performance.

Testing for Leaks

Method for identifying and fixing air leaks in connections.

Cleaning

Guidelines for cleaning the air compressor unit.

Pressure Switch

Information on the factory-set pressure switch operation.

Storage

Instructions for storing the air compressor for prolonged periods.

Troubleshooting

Specifications

Electrical Circuit

Diagram illustrating the electrical connections of the air compressor.

Air Passage Drawing

Diagram showing the flow of air through the compressor components.

California Air Tools Inc. Limited Warranty

Limited Warranty

Details on what the warranty covers and the process for repair or replacement.

Limited Warranty Periods

Specifies the duration of warranty coverage for different usage types.

Disclaimers, Limitations of Remedies & Exclusions

Outlines warranty disclaimers, limitations, and exclusions.

Product Registration

California Air Tools 10020AC Specifications

General

Model	10020AC
Tank Size	2.0 Gallons
Motor/Horsepower	1.0 HP
Maximum Pressure	120 PSI
Power Source	Electric
Pump Type	Oil-Free
Type	Ultra Quiet
Voltage	110V
Amperage	8.5 A