CAME Bpt TARGHA GSM VR1 - Real-time Control and Commands; Relay Activation During Calls

14
󱱮GSM signal quality
Function Displaying GSM signal quality
SMS Syntax <pin><command>
<pin> 0000 (Default)
<value> ‘range from...to’
SMS syntax example 0000Z
SMS reply example Signal level: 12
Automatic reply SMS Yes
NOTE. The command ‘Z’ analyses the quality of the GSM signal, and returns a
numerical value to the user: 0-1 (minimum), 17-23 (average), 31 (maximum)
Relay 1 activation
Function Relay 1 activation via sms
SMS Syntax <pin><command>
<pin> 0000 (Default)
<command> *
<value> 0, 1, 2, 3, 4, 5, 6, 7, 8, 9
SMS syntax example 0000*
SMS reply example Relay 1 activation
Automatic reply SMS Yes
NOTE. Activating relay 1 can also be carried out during an active call by press-
ing the * button on your phone keypad.
Relay 2 activation
Function Relay 2 activation via sms
SMS Syntax <pin><command>
<pin> 0000 (Default)
<command> #
<value> 0, 1, 2, 3, 4, 5, 6, 7, 8, 9
SMS syntax example 0000#
SMS reply example Relay 2 activation
Automatic reply SMS Yes
NOTE. Activating relay 2 can also be carried out during an active call by press-
ing the # button on your phone keypad.
Relay 1 closure time
Function Setting and/or modifying relay 1 closure time
SMS Syntax <pin><command><value>
<pin> 0000 (Default)
<command> **
<value> 0 (disabled), 1, 2, 3, 4, 5, 6, 7, 8, 9
SMS syntax example 0000**5
SMS reply example Relay closure time: 5
Automatic reply SMS Yes
Default 3
NOTE. The value is expressed in seconds
Relay 2 closure time
Function Setting and/or modifying relay 2 closure time
SMS Syntax <pin><command><value>
<pin> 0000 (Default)
<command> ##
<value> 0 (disabled), 1, 2, 3, 4, 5, 6, 7, 8, 9
SMS syntax example 0000##5
SMS reply example Relay closure time: 5
Automatic reply SMS Yes
Default 3
NOTE. The value is expressed in seconds
Commands during conversation
Increase speaker
volume
1 2 3
Increase micro-
phone sensitivity
Reduce
speaker volume
4 5 6
Reduce microphone
sensitivity
7 8 9
Relay 1 activation
* 0
#
Relay 2 activation
Ending the call *
The call is ended by pushing button ‘0’ only on telephones on xed networks.
Speaker Volume
If during the call the person you are talking to cannot hear your voice at the
right volume, you can increase the speaker volume by pressing key 1, or lower
it by pressing key 4.
Microphone Sensitivity
If you can’t hear the voice of the person in front of the audio entry panel, you
can press key 3 to increase or key 6 to reduce the sensitivity of the microphone.
Relay activation
Via the two relays, you can control the opening of a front door or automated
gate. This operation can be carried out during a call by pressing the button
to activate the rst relay, or pressing the button to activate the second relay.
NOTE: both relays cannot support voltages above 60V and currents with a
load over 500mA.
Ending the call
This function must be used when your GSM audio receiver device contacts a
number on a xed line. By pressing key ‘0’ you will stop the call.
NOTE: If button ‘0’ is not pressed, the call will remain on the line until the audio
receiver’s TIMEOUT time ( See parameter ‘H’ ).