Campbell Hausfeld WL6500 Series User Manual

WL6500 Series
¡[Assembly (con't)
For 10 inch diameter wheels, feed
the shoulder bolt through the top
hole on the tank axle iron and
tightly secure with the locknut.
Repeat on the opposite side.
3. When assembled, the tank must sit
level or slope slightly towards the
drain cock to allow the tank to
drain property.
Installation
LOCATION
It is extremely important to install the
compressor in a clean, well ventilated area
where the surrounding air temperature
will not be more than 100°F.
A minimum clearance of 18 inches
between the compressor and a wall is
required because objects could
‘obstruct air flow.
Do not locate the
‘compressor air
inlet near steam, paint spray, sandblast
areas or any other source of
contamination. This debris will damage
the motor.
‘grounding wire with an appropriate
grounding plug. Plug must be plugged
into an outlet that is property installed
and grounded in accordance with all
local codes and ordinances.
Grounding
AC
Grounded Outiet
1. This product is for use on a nominal
120 volt circuit and has a grounding
plug that looks lke the plug illustrated
in Fig. 3. Make sure the product is
connected to an outlet having the
same configuration as the plug. This
product must be grounded. in the
event of an electrical short circuit,
grounding reduces risk of electrical
shock by providing an escape wire for
electric current. This product is
equipped with a cord having a
Figure 3 - Grounding Method
LA DANGER!
Improper use of
grounding plug can re-
sutt in a possible risk of
electrical shock!
r- Do not use a
PATENT
grounding
adapter
with this product!
2. if repair or replacement of cord or plug
is necessary, do not connect grounding
wire to either flat blade terminal. The
wire with insulation having an external
surface that is green (with or without
yellow stripes) is the grounding wire.
[AWARNING) "over connect
WARNING) cren (or green and
yellow) wire to a live terminal.
3. Check with a qualified electrician or
serviceman if grounding instructions
are not completely understood, or if in
doubt as to whether product is
property grounded. Do not modi
plug provided; if it will not fit outlet,
have proper outlet installed by a
qualified electrician
‘WIRING
1. Local electrical wiring codes differ from
area to area. Source wiring, plug and
protector must be rated for at least the
amperage and voltage indicated on
motor nameplate, and meet all electrical
codes for this minimum.
2. Usea slow blow fuse or a circuit
breaker.
Overheating, short
[ACAUTION) Sing and re
rage wil resute trom inadequate
wane on
NOTE: 120 volt, 15 amp units can be
operated on a 120 voit creuit under the
following conditions:
a. No other electrical appliances or lights
are connected to the same branch
circuit.
b.
Voltage
supply
is
normal.
< Circuit is equipped with a 15 amp
circuit breaker or a 15 amp slow blow
fuse.
3. Hf these conditions cannot be met or if
nuisance tripping of current
protection device occurs, it may be
necessary to operate compressor from
a 120 voit, 20 amp circuit.
Pressure Switch - Auto/Off Switch - In
the ON position, the compressor shuts
off automatically when tank pressure
reaches the maximum preset pressure.
The compressor will automaticallly
restart when it reaches the minimum
preset pressure. In the OFF position,
the compressor will not operate.
‘switch should be in the OFF position
when connecting or disconnecting the
power cord from the electrical outlet
or when changing air tools.
Regulator - The regulator controls the
‘amount of air pressure released at the
hose outlet.
ASME Safety Valve - This valve
automatically releases air if the tank
pressure exceeds the preset maximum.
Handle - Designed to move the
compressor.
Tool Storage - 1/4 inch quick connect
couplers fit in holes to support air
chuck and other inflation fi

Campbell Hausfeld WL6500 Series Specifications

General

Brand	Campbell Hausfeld
Model	WL6500 Series
Category	Air Compressor
Language	English