To Next Page
K
Kylie MaldonadoAug 17, 2025
What to do if Campingaz ATTITUDE 2go burner will not light?
- EEric DavisAug 17, 2025
If the burner on your Campingaz Grill will not light, try blowing in the burner or cleaning the Venturi tube.
What to do if Campingaz ATTITUDE 2go burner will not light?
If the burner on your Campingaz Grill will not light, try blowing in the burner or cleaning the Venturi tube.
What to do if Campingaz ATTITUDE 2go Grill has difficulty in lighting up?
If you're having difficulty lighting up your Campingaz Grill, you can try the following: * Change the regulator if it does not match. * Reset the regulator. * Replace the hose and/or regulator if they are in poor condition. * Change the cylinder if necessary.
What to do if the grease ignites in Campingaz ATTITUDE 2go?
If grease ignites in an abnormal manner in your Campingaz Grill, it might be because grease has accumulated at the bottom of the grill. You should reduce the gas flow of the barbecue and clean the bottom of the grill.
Why Campingaz ATTITUDE 2go Grill burner does not burn smoothly?
If the burner on your Campingaz Grill does not burn smoothly or goes out, it may be due to insufficient gas in the cylinder. Change the gas cylinder to resolve this issue.
How to fix large flame on the Campingaz ATTITUDE 2go burner surface?
A large flame on the burner surface of your Campingaz Grill may be because the burner outlet is blocked (spider webs, etc.) or the injector holder is improperly positioned in the outlet. Clean the Venturi tube and/or reposition the burner.
What to do if there is flame at the injector of my Campingaz ATTITUDE 2go Grill?
If you notice a flame at the injector of your Campingaz Grill, check that the cylinder is not almost empty and change the cylinder if needed. For further assistance, it is recommended to contact the After Sales Service.
Why Campingaz Grill has insufficient cooking temperature?
If your Campingaz Grill has an insufficient cooking temperature, it might be because the injector or Venturi tube is blocked (spider webs...). Clean the Venturi tube to resolve this.
What to do if Campingaz ATTITUDE 2go Grill burner does not light up with the piezo ignitor?
If the burner on your Campingaz Grill does not light up with the piezo ignitor, check the condition of the wires or electrodes and change them if necessary. Also, check that the piezo ignitor is well connected to the electrode; connect if necessary. For further assistance, it is recommended to contact the After Sales Service.
What to do if there is flame behind the adjustment button (knob) of my Campingaz ATTITUDE 2go Grill?
If you observe a flame behind the adjustment button (knob) of your Campingaz Grill, immediately turn the appliance off and close the cylinder. For further assistance, it is recommended to contact the After Sales Service.
Why Campingaz Grill flames are not stable when a new cylinder is used?
If the flames are not stable on your Campingaz Grill when using a new cylinder, it could be due to the presence of air in the cylinder and, consequently, in the gas circuit. Simply let the barbecue work, and the problem should disappear as the air clears out.
Fit hose tightly to appliance and regulator, secure with clamps. Verify sealing.
Attach hose with G 1/2 and M20x1.5 nuts to appliance and regulator. Use wrenches to tighten.
Press control knob, turn counterclockwise to full flow, push piezo switch.
If electronic ignition fails, use manual lighting with a match and control knob.
Clean burner with damp sponge and possibly a wet steel brush. Ensure outlets are clear.
Clean control panel with a sponge and dishwashing liquid. Avoid abrasive products.
Clean the bottom of the grill after each use with a damp sponge.
Clean tray after each use. Sand can be used to absorb grease.
Clean cooled grids with a specific cleaner and brushes or in the dishwasher.
Check regulator, safe mode, hose condition, and cylinder level.
Possible air in cylinder or gas circuit. Let barbecue run to clear.
Check hose, injector, tap, venturi tube, and burner holes for blockages.
Check gas supply in cylinder or clean venturi tube/reposition burner.
Check cylinder level or clean venturi tube/reposition burner.
Check cylinder level or clean venturi tube.
Check injector/Venturi tube for blockages or accumulated grease.
Ensure grease is not accumulated at the bottom of the grill.
Check wires, electrodes, and piezo ignitor connection.
Check air tightness of coupling and presence of flat seal.
Turn appliance off, close cylinder, and contact after-sales service.
General