Candy CDIH 2D949 User Manual (English)

Questions and Answers:

W
Walter RobinsonAug 5, 2025
Why are the dishes not clean after using my Candy CDIH 2D949?
- S
  Stephen JamesAug 5, 2025
  If the dishes are not clean after a cycle in your Candy Dishwasher, consider these potential causes: clogged filters (clean them); incorrectly assembled filters (ensure correct assembly); clogged spray arms (remove food remnants); an inappropriate programme for the load (select a more suitable programme); incorrect item placement (rearrange items); blocked spray arms (adjust item placement); insufficient detergent (use the correct amount); or cycle interruption (avoid opening the door during the wash).
T
Terry YangAug 10, 2025
Why is the Salt Aid Indicator lighted on my Candy CDIH 2D949 Dishwasher?
- R
  Richard JonesAug 10, 2025
  If the Salt Aid Indicator is lit on your Candy Dishwasher, it means the softener salt is empty (fill the tank until full) or the refill of salt was not confirmed (press the button for 3 seconds after each refill).
L
lterryAug 14, 2025
Why is the Rinse Aid Indicator lighted on my Candy CDIH 2D949?
- J
  Jennifer HudsonAug 14, 2025
  If the Rinse Aid Indicator is lit on your Candy Dishwasher, it means the rinse aid dispenser is empty (refill it until full) or the refill was not confirmed (press the button for 3 seconds after each refill).
T
Tammy GarciaAug 18, 2025
Why does my Candy Dishwasher leave streaks on glasses?
- B
  brianjonesAug 18, 2025
  Whitish streaks, stains, or bluish layers on glasses and dishes from your Candy Dishwasher can be caused by too much rinse aid (decrease the amount released), too much detergent (use the correct quantity), or the use of Multitab detergent tablets with a short programme (select a longer programme).
M
Maria HernandezAug 22, 2025
What to do if my Candy CDIH 2D949 shows ALARMCODE E10 and doesn't fill with water?
- M
  Marilyn FloydAug 22, 2025
  The Candy Dishwasher might not be filling with water due to several reasons: the water tap could be closed (open it); the water inlet hose might be kinked (correct its position); the aqua-stop system may be triggered (the hose must be replaced); the filter in the water inlet hose could be clogged (clean it); the water inlet might be clogged (check water flow from tap); or the water pressure might be too low (contact your local water authority). If you solved the error, switch off the appliance and restart the programme.
L
Luke LeachAug 27, 2025
What to do if my Candy Dishwasher shows ALARMCODE E20?
- A
  awardAug 27, 2025
  If your Candy Dishwasher displays ALARMCODE E20, it indicates a drainage problem. Possible causes include clogged filters (clean them) or a blocked drain (ensure the drain water connection and piping are clear). In both cases, scoop out as much water as possible and continue the programme by pressing the START/PAUSE button.
R
Robert ClineAug 31, 2025
What does ALARMCODE E30 mean on my Candy Dishwasher?
- C
  cmillerAug 31, 2025
  If your Candy Dishwasher displays ALARMCODE E30 and the drain pump runs permanently, it indicates a leak. This could be due to water leakages, a blocked water inlet valve, or a blocked drainage. To resolve this: close the water tap, disconnect the appliance from the power supply, and contact service.

Candy CDIH 2D949 Specifications

General

Door color	White
Door hinge	Standard
Product size	Slimline (45 cm)
Built-in display	Yes
Lower basket rack	Foldable
Custom panel-ready	-
Appliance placement	Fully built-in
Control panel color	Black
Lower basket rack type	Double
Lower basket safety stop	No
Cycle time	298 min
Noise level	49 dB
Drying system	Condensation
Delay start (max)	23 h
Number of place settings	9 place settings
Number of washing programs	7
Current	10 A
Power plug type	Type F (CEE 7/4)
AC input voltage	230 V
Energy efficiency scale	A to G
Water consumption per cycle	9 L
Package width	485 mm
Package height	620 mm
Package weight	41000 g