EasyManua.ls Logo

Candy RP 4106BWMR/1-S - User Manual

Candy RP 4106BWMR/1-S
144 pages
Go to English
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
IT
DE
EN
ES
FR

Questions and Answers

  • K
    Keith HullAug 20, 2025
    Why my Candy RP 4106BWMR/1-S Washer does not work / start?
    • J
      Jeffrey ButlerAug 20, 2025
      If your Candy Washer doesn't start, ensure it's plugged into a working socket and that the power is on. Test the socket with another appliance. Also, make sure the door is correctly closed, the program is properly selected, the start button is pressed, and that the machine isn't in pause or time delay mode.
  • E
    Erin Gibbs PhDAug 22, 2025
    What to do if water leaked on the floor near Candy RP 4106BWMR/1-S Washer?
    • A
      Alexis KellyAug 22, 2025
      If you see water leaking near your Candy Washer, it could be from a faulty seal between the tap, supply hose, and fill valve. Try replacing the seal and tightening the hose connections. Also, check that the front filter is correctly closed.
  • P
    Patrick BanksAug 25, 2025
    What to do if Candy RP 4106BWMR/1-S Washer does not spin?
    • K
      Krista MataAug 25, 2025
      If your Candy Washer isn't spinning, first remove and de-tangle the load, then reload and restart the spin program. Ensure that the water has completely drained. Also, check that the 'no spin' function isn't selected and that you're using the correct amount of detergent, as excessive detergent can impede the spin cycle. Check the selected options and their effect on the spin cycle. If the problem persists, refer to Error 3 section.
  • H
    hannah20Aug 26, 2025
    What to do if Candy RP 4106BWMR/1-S shows error E3 (with display) 3 flashes of the LEDs (without display)?
    • S
      Shelby BaileyAug 27, 2025
      If your Candy Washer displays error 'E3' or shows 3 LED flashes, check that the filter isn't clogged and that there are no foreign objects in the filter compartment. Ensure the drain hose isn’t bent or trapped and that the home drainage system isn't blocked. Try draining water in the sink to test the drainage.
  • D
    Dana TaylorAug 28, 2025
    Why Candy RP 4106BWMR/1-S does not work / start?
    • E
      Erik JonesAug 28, 2025
      If your Candy Washer doesn't start, check these things: First, ensure the appliance is properly plugged into a working electrical outlet and that the power is on. Test the wall socket with another device, like a lamp, to confirm it's functioning. Make sure the door is completely closed. Also, verify that you've correctly selected the desired program and pressed the start button. Finally, check that the washer isn't in pause or time delay mode.
  • E
    Eric ReyesAug 29, 2025
    What to do if Candy Washer doesn't drain water?
    • L
      Lauren SextonAug 30, 2025
      If your Candy Washer isn't draining, start by checking the filter for clogs or foreign objects that might be blocking water flow. Also, make sure the drain hose isn't bent, kinked, or trapped. Finally, ensure that your home drainage system isn't blocked; try draining water into a sink to verify.
  • C
    Craig SullivanAug 31, 2025
    What to do if Candy Washer doesn't spin?
    • A
      Andrea BrownSep 1, 2025
      If your Candy Washer isn't spinning, it might be due to an unbalanced load. Remove the laundry, untangle it, reload it evenly, and restart the spin program. Also, ensure water has completely drained from the machine. Check if the 'no spin' function is selected. Excessive detergent usage can also prevent spinning, so use the correct amount.
  • K
    Kristen TorresSep 2, 2025
    What to do if Candy RP 4106BWMR/1-S leaked on the floor?
    • T
      Timothy KelleySep 2, 2025
      If you find water leaking near your Candy Washer, it could be leaking from the seal between the tap, supply hose, and fill valve. Replace the seal and tighten the hose connections properly. Also, make sure the front filter is correctly closed.
  • M
    mathewselizabethSep 4, 2025
    Why strong vibrations / noises are heard during the spin cycle of Candy RP 4106BWMR/1-S?
    • A
      Austin TravisSep 4, 2025
      Loud noises or strong vibrations during the spin cycle of your Candy Washer may occur if the appliance isn't level. Adjust the feet as needed. Also, ensure that the transport screws, rubber bungs, and spacer tubes have been removed and that there are no foreign objects inside the drum.
  • S
    Samantha Colon MDSep 6, 2025
    How to fix Candy Washer error E2 (with display) 2 flashes of the LEDs (without display)?
    • B
      Brian BennettSep 6, 2025
      If your Candy Washer displays 'E2' or the LEDs flash twice, ensure the water supply tap is open and the supply hose isn’t bent or trapped. Check that the drain pipe is at the correct height. Close the tap, unscrew the filler hose, and clean the anti-sand filter. Also, inspect the filter for clogs or foreign objects.

Candy RP 4106BWMR/1-S Specifications

General IconGeneral
TypeWasher
Loading typeFront load
Capacity10 kg
Spin Speed1400 RPM
Energy Efficiency ClassA
Dimensions (HxWxD)85x60x58 cm
Weight65 kg
ColorWhite
Energy RatingA

Related product manuals