Why my Candy Washer does not start?
If your Candy Washer isn't starting, there are several things to check: * Ensure the washer is plugged into a working power socket and that the power is on. * Test the wall socket with another appliance. * Make sure the door is correctly closed. * Verify that you've selected the correct program and pressed the start button. * Confirm the washing machine isn't in pause or time delay mode.
What to do if my Candy RP4 476BWMR/1-S Washer does not spin?
If your Candy Washer isn't spinning, here are a few things to consider: * The washer has a system that detects unbalanced loads. If the load isn't balanced, the machine may try to balance it, reduce the spin speed, or abort the spin cycle. Try removing, detangling, and reloading the laundry. * Wait a few minutes to see if the water drains completely. If not, refer to the Error 3 section. * Ensure the "no spin" function isn't selected (if your model has one). * Check the selected options and their impact on the spin cycle. * Using too much detergent can also prevent spinning; use the correct amount.
Why is my Candy RP4 476BWMR/1-S Washer leaking water?
If you notice water leaking near your Candy Washer: * Check the seal between the tap, supply hose, and fill valve for leaks. If necessary, replace the seal and tighten the hose connections. * Ensure that the front filter is correctly closed.
How to fix E2 error on Candy Washer?
The E2 error on your Candy Washer indicates that the machine cannot load water. To resolve this: * Ensure the water supply tap is fully open. * Check that the water supply hose isn’t bent, kinked, or trapped. * Verify the drain pipe is at the correct height (refer to the installation section). * Close the water supply tap, detach the filler hose from the back, and clean the anti-sand filter. * Inspect the filter for clogs or foreign objects that may be blocking water flow.
What to do if my Candy RP4 476BWMR/1-S shows E3 error?
If your Candy Washer displays an E3 error, it means the machine isn't draining water. Here's what you can do: * Check the filter for any clogs or foreign objects that might be obstructing water flow. * Make sure the drain hose isn’t bent, kinked, or trapped. * Ensure your home drainage system isn't blocked. Try draining water into a sink to check.
Why is my Candy RP4 476BWMR/1-S Washer vibrating so much during spin cycle?
Excessive vibrations or noises during the spin cycle of your Candy Washer can be due to several reasons: * The washing machine might not be level. Adjust the feet as described in the relevant section. * Ensure that the transport screws, rubber bungs, and spacer tubes have been removed. * Check for any foreign objects inside the drum, such as coins, hinges, or buttons.
How to solve E7 error on Candy RP4 476BWMR/1-S Washer?
The E7 error on your Candy Washer indicates a door problem. Try these steps: * Ensure the door is correctly closed and that no clothes are preventing it from closing fully. * If the door is locked, turn off and unplug the washing machine, wait 2-3 minutes, and then try reopening the door.
What to do if Candy Washer displays E4 error?
The E4 error on your Candy Washer indicates too much foam and/or water. Make sure you're using the correct amount of detergent, and that the detergent is designed for use in a washing machine.
General| Loading type | Front |
|---|---|
| Load Capacity | 7 kg |
| Spin Speed | 1400 RPM |
| Colour | White |
| Noise Level (Washing) | 58 dB |
| Noise Level (Spinning) | 79 dB |
| Type | Washer |
| Dimensions (H x W x D) | 85 x 60 x 45 cm |
| Programs | Cotton, Synthetics |
To Next Page