Why my Candy Washer does not work / start?
If your Candy Washer doesn't start, ensure it's plugged into a working socket and that the power is on. Test the socket with another appliance. Also, make sure the door is correctly closed, the program is properly selected, the start button is pressed, and that the machine isn't in pause or time delay mode.
What to do if Candy Washer does not spin?
If your Candy Washer isn't spinning, first remove and de-tangle the load, then reload and restart the spin program. Ensure that the water has completely drained. Also, check that the 'no spin' function isn't selected and that you're using the correct amount of detergent, as excessive detergent can impede the spin cycle. Check the selected options and their effect on the spin cycle. If the problem persists, refer to Error 3 section.
What to do if Candy Washer shows error E3 (with display) 3 flashes of the LEDs (without display)?
If your Candy Washer displays error 'E3' or shows 3 LED flashes, check that the filter isn't clogged and that there are no foreign objects in the filter compartment. Ensure the drain hose isn’t bent or trapped and that the home drainage system isn't blocked. Try draining water in the sink to test the drainage.
What to do if water leaked on the floor near Candy RO 1494DWME/1-S?
If you see water leaking near your Candy Washer, it could be from a faulty seal between the tap, supply hose, and fill valve. Try replacing the seal and tightening the hose connections. Also, check that the front filter is correctly closed.
Why strong vibrations / noises are heard during the spin cycle of Candy Washer?
Loud noises or strong vibrations during the spin cycle of your Candy Washer may occur if the appliance isn't level. Adjust the feet as needed. Also, ensure that the transport screws, rubber bungs, and spacer tubes have been removed and that there are no foreign objects inside the drum.
How to fix Candy RO 1494DWME/1-S Washer error E2 (with display) 2 flashes of the LEDs (without display)?
If your Candy Washer displays 'E2' or the LEDs flash twice, ensure the water supply tap is open and the supply hose isn’t bent or trapped. Check that the drain pipe is at the correct height. Close the tap, unscrew the filler hose, and clean the anti-sand filter. Also, inspect the filter for clogs or foreign objects.
How to resolve Candy RO 1494DWME/1-S Washer error E7 (with display) 7 flashes of the LEDs (without display)?
If your Candy Washer displays 'E7' or the LEDs flash 7 times, make sure the door is correctly closed and that clothes aren't preventing it from fully closing. If the door is locked, turn off and unplug the washer, wait 2-3 minutes, and then reopen the door.
What to do if Candy Washer shows error E4 (with display) 4 flashes of the LEDs (without display)?
If your Candy Washer displays 'E4' or flashes the LEDs 4 times, make sure you are using the correct amount of detergent and that the detergent is designed for use in a washing machine.
General| Capacity | 9 kg |
|---|---|
| Spin Speed | 1400 rpm |
| Energy Efficiency Class | A+++ |
| Colour | White |
| Built-in display | Yes |
| Door colour | White |
| Control type | Electronic |
| Drum material | Stainless Steel |
| Spin-drying class | B |
| Washing class | A |
| Delay start | Yes |
| Delayed start time | 24 hours |
| Near Field Communication (NFC) | Yes |
| Wi-Fi controlled | No |
| Loading type | Front load |
| Dimensions (HxWxD) | 850 x 600 x 530 mm |
| Water consumption | 50 L |
To Next Page