EasyManua.ls Logo

Candy RO4 476DWMC7/1-S - User Manual

Candy RO4 476DWMC7/1-S
132 pages
Go to English
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
IT
DE
EN
ES
FR

Questions and Answers

  • L
    lambertanthonyAug 21, 2025
    What to do if water leaked on the floor near Candy Washer?
    • J
      jenniferwongAug 21, 2025
      If you see water leaking near your Candy Washer, it could be from a faulty seal between the tap, supply hose, and fill valve. Try replacing the seal and tightening the hose connections. Also, check that the front filter is correctly closed.
  • S
    Sheena BellAug 25, 2025
    What to do if Candy RO4 476DWMC7/1-S Washer does not spin?
    • A
      Andrew HarrisAug 25, 2025
      If your Candy Washer isn't spinning, first remove and de-tangle the load, then reload and restart the spin program. Ensure that the water has completely drained. Also, check that the 'no spin' function isn't selected and that you're using the correct amount of detergent, as excessive detergent can impede the spin cycle. Check the selected options and their effect on the spin cycle. If the problem persists, refer to Error 3 section.
  • V
    Vanessa BakerAug 26, 2025
    What to do if Candy RO4 476DWMC7/1-S Washer shows error E3 (with display) 3 flashes of the LEDs (without display)?
    • C
      Crystal AustinAug 26, 2025
      If your Candy Washer displays error 'E3' or shows 3 LED flashes, check that the filter isn't clogged and that there are no foreign objects in the filter compartment. Ensure the drain hose isn’t bent or trapped and that the home drainage system isn't blocked. Try draining water in the sink to test the drainage.
  • E
    erin97Aug 28, 2025
    Why my Candy RO4 476DWMC7/1-S does not start?
    • C
      colleen78Aug 28, 2025
      If your Candy Washer isn't starting, ensure it's plugged into a working socket and that the power is on. Test the wall socket with another appliance. Also, check that the door is correctly closed, the program is correctly selected, the start button is pressed, and that the machine isn't in pause or time delay mode.
  • J
    jose44Aug 30, 2025
    What to do if my Candy RO4 476DWMC7/1-S does not spin?
    • M
      Mr. Eric OchoaAug 30, 2025
      If your Candy Washer isn't spinning, it might be due to an unbalanced load. Remove the load, de-tangle it, reload it, and restart the spin program. Also, ensure that water has been completely drained from the washer. Check if the 'no spin' function is selected and review your selected options, as they may affect the spin cycle. Excessive detergent can also impede spinning, so ensure you're using the correct amount.
  • A
    Annette MooreSep 1, 2025
    How to fix water leak from Candy RO4 476DWMC7/1-S?
    • M
      Melissa Ballard MDSep 1, 2025
      If you notice water leaking near your Candy Washer, it could be due to a leak from the seal between the tap, supply hose, and fill valve. In this case, replace the seal and tighten the hose connections correctly. Also, ensure that the front filter is correctly closed.
  • M
    michael37Sep 3, 2025
    Why strong vibrations / noises are heard during the spin cycle of Candy RO4 476DWMC7/1-S?
    • S
      scarterSep 3, 2025
      Loud noises or strong vibrations during the spin cycle of your Candy Washer may occur if the appliance isn't level. Adjust the feet as needed. Also, ensure that the transport screws, rubber bungs, and spacer tubes have been removed and that there are no foreign objects inside the drum.
  • Y
    ydelgadoSep 5, 2025
    How to fix Candy Washer error E2 (with display) 2 flashes of the LEDs (without display)?
    • L
      lisachoiSep 6, 2025
      If your Candy Washer displays 'E2' or the LEDs flash twice, ensure the water supply tap is open and the supply hose isn’t bent or trapped. Check that the drain pipe is at the correct height. Close the tap, unscrew the filler hose, and clean the anti-sand filter. Also, inspect the filter for clogs or foreign objects.
  • B
    Bethany AlvarezSep 7, 2025
    How to resolve Candy RO4 476DWMC7/1-S error E7 (with display) 7 flashes of the LEDs (without display)?
    • D
      Dana HansenSep 7, 2025
      If your Candy Washer displays 'E7' or the LEDs flash 7 times, make sure the door is correctly closed and that clothes aren't preventing it from fully closing. If the door is locked, turn off and unplug the washer, wait 2-3 minutes, and then reopen the door.
  • J
    Jonathan RodriguezSep 10, 2025
    What to do if Candy RO4 476DWMC7/1-S displays E7 error?
    • Q
      qfryeSep 10, 2025
      If your Candy Washer displays error code E7, make sure the door is correctly closed and that clothes inside the drum aren't preventing it from fully closing. If the door is locked, turn off and unplug the washing machine, wait 2-3 minutes, and then reopen the door.

Candy RO4 476DWMC7/1-S Specifications

General IconGeneral
Load Capacity7 kg
Spin Speed1400 rpm
Energy Efficiency ClassA
Number of Programs16
Display TypeDigital
Dimensions (H x W x D)85 x 60 x 45 cm
Washer typeFront Load
Spin-drying efficiency classB
ConnectivityWi-Fi + Bluetooth
Depth45 cm
ColorWhite
Water Consumption41 L

Related product manuals