Why my Candy RP586BWMBCB/1-S does not work / start?
If your Candy Washer doesn't start, ensure it's plugged into a working socket and that the power is on. Test the socket with another appliance. Also, make sure the door is correctly closed, the program is properly selected, the start button is pressed, and that the machine isn't in pause or time delay mode.
What to do if water leaked on the floor near Candy RP586BWMBCB/1-S Washer?
If you see water leaking near your Candy Washer, it could be from a faulty seal between the tap, supply hose, and fill valve. Try replacing the seal and tightening the hose connections. Also, check that the front filter is correctly closed.
What to do if Candy Washer does not spin?
If your Candy Washer isn't spinning, first remove and de-tangle the load, then reload and restart the spin program. Ensure that the water has completely drained. Also, check that the 'no spin' function isn't selected and that you're using the correct amount of detergent, as excessive detergent can impede the spin cycle. Check the selected options and their effect on the spin cycle. If the problem persists, refer to Error 3 section.
What to do if Candy RP586BWMBCB/1-S Washer shows error E3 (with display) 3 flashes of the LEDs (without display)?
If your Candy Washer displays error 'E3' or shows 3 LED flashes, check that the filter isn't clogged and that there are no foreign objects in the filter compartment. Ensure the drain hose isn’t bent or trapped and that the home drainage system isn't blocked. Try draining water in the sink to test the drainage.
Why is my Candy Washer not spinning?
To address the issue of your Candy Washer not spinning, consider the following: The machine may be trying to balance the load, which increases spin time or reduces spin speed. If this happens, remove, detangle, and reload the laundry. Also, make sure a "no spin" function isn't selected. Check selected options and their impact on the cycle and ensure you're using the correct amount of detergent, as excessive detergent can hinder spinning. If the problem persists, and water hasn't completely drained, refer to the Error 3 section.
Why is water leaking from my Candy Washer?
If you find water leaked on the floor near your Candy Washer, it may be due to a leak from the seal between the tap, supply hose, and fill valve. If so, replace the seal and tighten the hose connections properly. Also, make sure the front filter is correctly closed.
Why strong vibrations / noises are heard during the spin cycle of Candy RP586BWMBCB/1-S?
Loud noises or strong vibrations during the spin cycle of your Candy Washer may occur if the appliance isn't level. Adjust the feet as needed. Also, ensure that the transport screws, rubber bungs, and spacer tubes have been removed and that there are no foreign objects inside the drum.
How to fix Candy Washer error E2 (with display) 2 flashes of the LEDs (without display)?
If your Candy Washer displays 'E2' or the LEDs flash twice, ensure the water supply tap is open and the supply hose isn’t bent or trapped. Check that the drain pipe is at the correct height. Close the tap, unscrew the filler hose, and clean the anti-sand filter. Also, inspect the filter for clogs or foreign objects.
How to resolve Candy RP586BWMBCB/1-S error E7 (with display) 7 flashes of the LEDs (without display)?
If your Candy Washer displays 'E7' or the LEDs flash 7 times, make sure the door is correctly closed and that clothes aren't preventing it from fully closing. If the door is locked, turn off and unplug the washer, wait 2-3 minutes, and then reopen the door.
What to do if my Candy Washer shows E2 error?
If your Candy Washer displays error code E2 or the LEDs flash twice, ensure the water supply tap is fully open and the supply hose isn’t bent or trapped. Also, check that the drain pipe is at the correct height as per the installation instructions. Close the tap and inspect the “anti-sand” filter for blockages. Finally, check the filter for clogs or foreign objects obstructing water flow.
To Next Page
General