B
Beverly AlvarezAug 20, 2025
Why image will not appear on Canon XL 2 Camcorder screen?
- MMonica AveryAug 20, 2025
If the image is not appearing on the screen of your Canon Camcorder, ensure that the POWER dial is set to a recording program.
To Next PageTo Next PageWhy image will not appear on Canon XL 2 Camcorder screen?
If the image is not appearing on the screen of your Canon Camcorder, ensure that the POWER dial is set to a recording program.
Why is Canon Camcorder viewfinder picture blurred?
If the viewfinder picture on your Canon Camcorder is blurred, adjust the viewfinder with the dioptric adjustment lever.
What to do if pressing the start/stop button will not start recording on Canon XL 2?
If pressing the start/stop button on your Canon Camcorder doesn't initiate recording, several factors could be at play. First, check if a cassette is loaded. Second, verify that the POWER dial is set to a recording program. Finally, ensure the lock lever on the carrying handle is deactivated by sliding it to the left.
Why does Canon XL 2 Camcorder switch off by itself?
If the Canon Camcorder switches off by itself, the power save function may have been activated. Turn the camcorder on.
What to do if pressing the playback button does not start playback on Canon XL 2 Camcorder?
If pressing the playback button on your Canon Camcorder does not start playback, ensure the camcorder is set to VCR mode. Also, verify that a cassette is loaded.
Why does Canon XL 2 viewfinder switches on and off?
If the viewfinder on your Canon Camcorder switches on and off, the battery pack may be exhausted. Replace or charge the battery pack.
What to do if “SET THE TIME ZONE, DATE AND TIME” appears on Canon XL 2 Camcorder screen?
If you see “SET THE TIME ZONE, DATE AND TIME” on your Canon Camcorder screen, it means the time zone, date and time are not set, or the backup battery is exhausted. Set the time zone, date and time, or replace the backup battery and reset the date and time.
Why audio is not recorded on Canon XL 2?
If the audio is not being recorded on your Canon Camcorder, make sure the INPUT SELECT switch is set to the correct position. Also, if the REC LEVEL switch is set to M, ensure the recording level is adjusted correctly.
Why audio is recorded in a very low level on Canon XL 2?
If the audio is recorded at a very low level on your Canon Camcorder, and you have a microphone connected to the XLR terminal, it might need phantom power. Set the +48V switch to ON. Also, check if the microphone attenuator is turned on; if so, set the MIC ATT. switch to OFF.
Why Canon Camcorder buttons will not work?
If the buttons on your Canon Camcorder will not work, load a cassette.
Power| power supply | 7.2V DC |
|---|---|
| power consumption | 7.1W |
Camera Sensor| image sensor size | 1/3" |
|---|---|
| image sensor pixels | 680, 000 pixels |
| target area 16:9 pixels | 460, 000 pixels |
Recording| video recording system | DV System |
|---|---|
| audio recording system | PCM digital recording |
| tape speed SP | 0.74 ips |
Display| viewfinder size | 2.0-inch |
|---|---|
| viewfinder pixels | 200, 000 pixels |
| viewfinder configuration | RGB delta |
Operating Environment| operating temperature | 32–104˚ F |
|---|---|
| minimum illumination | 5.5 lx |
| recommended subject illumination | More than 100 lx |
Ports & interfaces| dv terminal | 4-pin connector |
|---|---|
| s-video terminal | 4-pin mini-DIN |
| audio terminal | RCA pin jack |
Weight and Dimensions| dimensions (W x H x D) | 8.9 x 8.7 x 19.5 in. |
|---|---|
| weight (camcorder body only) | 5.3 lbs. |
| total equipped weight | 7.8 lbs. |
