57
ENG
pRack +0300025EN rel. 1.3 - 17.12.2015
Mask index Display Description Description Default UOM Values
Bba54
Heat reclaim pump
force
Manual operating status for heat recovery pump (line 1) OFF --- OFF / ON
Bba55
ChillBooster
force
Manual operating status for ChillBooster (line 1) OFF --- OFF / ON
Bba57
Fan1
force
Manual operating status for fan 1 (line 2) OFF --- OFF / ON
…
…………
Bba72
Fan16
force
Manual operating status for fan 16 (line 2) OFF --- OFF / ON
Bba73
Heat reclaim pump
force
Manual operating status for heat recovery pump (line 2) OFF --- OFF / ON
Bba74
ChillBooster
force
Manual operating status for ChillBooster (line 2) OFF --- OFF / ON
Bbb05
Compressor 1
Force to
Manual continuous capacity request for compressor 1 (line 1) 0.0 % 0.0…100.0
Bbb06
Oil cool pump
Force to
Manual request for oil cooling pump (line 1) 0.0 % 0.0…100.0
Bbb07
Compressor 1
Force to
Manual continuous capacity request for compressor 1 (line 2) 0.0 % 0.0…100.0
Bbb08
Oil cool pump
Force to
Manual request for oil cooling pump (line 2) 0.0 % 0.0…100.0
Bbb09
Fan1
Force to
Manual continuous capacity request for fan 1 (line 1) 0.0 % 0.0…100.0
Bbb10
Heat reclaim pump
force
Manual request for heat recovery pump (line 1) 0.0 % 0.0…100.0
Bbb11
Fan1
Force to
Manual continuous capacity request for fan 1 (line 2) 0.0 % 0.0…100.0
Bbb12
Heat reclaim pump
force
Manual request for heat recovery pump (line 2) 0.0 % v
Bc01
Test Dout Enable DO test mode NO --- NO / YES
Timeout Test mode duration after last button pressed 10 min 0…500
Bc02
Test Aout Enable AO test mode NO --- NO / YES
Timeout Test mode duration after last button pressed 10 min 0…500
Bca10
DO1 DO 1 logic for test NO --- NO / NC
DO 1 value for test OFF --- OFF / ON
…… … ………
Bca26
DO29 DO 29 logic for test NO --- NO / NC
DO 29 value for test OFF --- OFF / ON
Bcb10 AO1 AO 1 value for test 0.0 --- 0.0…100.0
…… ………
Bcb12
AO6 AO 6 value for test 0.0 --- 0.0…100.0
Mask index Display description Description Default UOM Values
C.Compressors(*) (The I/Os available depend on the selected confi guration, the following are just some examples. For the complete list of I/O positions available see
Appendix A.5)
Caa01
DI Alarm 1 for compressor 1 DI position (line 1) 03 --- ---, 01…18, B1…B10 (****)
Status (display only) Status of alarm 1 for compressor 1 DI (line 1) --- --- Closed / Open
Logic Logic of alarm 1 for compressor 1 DI (line 1) NC --- NC / NO
Function (display only) Alarm 1 for compressor 1 function status (line 1) --- --- Not active / Active
…… … ………
Caa08
Line relay DO Compressor 1 part winding or star DO position and status (On/Off )
display (line 1)
… --- ---, 01…29 (****)
Part winding DO/Star
relay DO (*)
Compressor 1 delta DO position and status (On/Off ) display (line 1) … --- ---, 01…29 (****)
---/ Delta relay DO (*) Compressor 1 line DO position and status (On/Off ) display (line 1) … --- ---, 01…29 (****)
Logic DO logic to start compressor 1 (line 1) NC --- NC / NO
Caa09
DO Unloader 1 for compressor 1 DO position (line 1) … --- ---, 01…29 (****)
Status (display only) Status of unloader 1 for compressor 1 DI (line 1) --- --- Closed / Open
Logic Logic of unloader 1 for compressor 1 DI (line 1) NC --- NC / NO
Function (display only) Unloader 1 for compressor 1 function status (line 1) --- --- Not active / Active
…… … ………
Caa14
AO Compressor modulating device AO position (line 1) 0 --- ---, 01…06 (****)
Type (****)
Type of output, PWM / phase control for compressor modulating device
(line 1)
FCS1*-CON-
VONOFF
---
----
FCS1*-CONVONOFF
FCS3*-CONV010"
Status (display only) Modulating device output value (line 1) 0 % 0.0…100.0
…… … ………
Caaal
--- Suction pressure probe position (line1) B1 --- ---, B1…B10 (****)
--- Suct pressure probe type (line 1) 4-20mA --- ----
0-1V
0-10V
4-20mA
0-5V
--- (display only) Suction temperature value (line 1) --- … … (**)
Upper value Suct pressure maximum limit (line 1) 7,0 barg … … (**)
Lower value Suct pressure minimum limit (line 1) -0,5 barg … … (**)
Calibration Suction pressure probe adjustment (line 1) 0.0 barg … … (**)
…… … ………
Cab01
Regulation by Compressor control by temperature or pressure (line 1) PRESSURE --- PRESSURE TEMPERATURE
Regulation type Compressor control type (line 1) NEUTRAL
ZONE
--- PROPORTIONAL BAND
NEUTRAL ZONE
Cab02
Minimum Compressor setpoint lower limit (line 1) … (**) … … (**)
Maximum Compressor setpoint higher limit (line 1) … (**) … … (**)
Cab03 Setpoint Compressor setpoint (line 1) … (**) … … (**)
To Next Page
Loading...
