5
2-7/16"
1-1/8"
28-7/8"
(733mm)
25-1/4"
22-9/16"
JUNCTION BOX
LOCATION
7/8" DI A
ACCESSORY
1/2" DIA THERMOSTAT
WIRE ENTRY
3-15/16"
LEFT HAND GAS
ENTRY
33-5/16"
24-7/8"
5-1/2"
7/8" DIA. ACCESSORY
11/16"
21-5/8"
BOTTOM INLE T
1-11/16"
13/16"
11/16"
4-13/16"
AIRFLOW
19"
OUTLE T
13/16"
11/16"
8-9/16"
VENT OUTLE T
5 PLACES (TYP)
3-3/4"
1-3/4" DIA.RIGHT HAND
GAS ENTRY
7/8" DIA. K.O. WIRE ENTRY
SIDE INLE T
14-7/8"
7/8" DIA. ACCESSORY
1-1/4"
1"
22-1/16"
A
D
F
E
(FLUE COLLAR)
5-15/16"
24"
CASING
1-5/16"
1/2" DIA. K.O.THERMOSTAT
WIRE ENTRY
ALTERNAT E
JUNCTION BOX
LOCATIONS (TYP)
26-1/8"
1-1/2"
7-3/4"
9-5/8"
11-1/2"
5-1/2"
(664mm)
(641mm)
(573mm)
(22mm)
(846mm)
(17mm)
(549mm)
610mm
(43mm)
(140mm)
(632mm)
(17mm)
(140mm)
(95mm)
(21mm)
(122mm)
(217mm)
(62mm)
(33mm)
(29mm)
(483mm)
(13mm)
(44mm)
(22mm)
(22mm)
(38mm)
(560mm)
(25mm)
(32mm)
(378mm)
(17mm)
(197mm)
(244mm)
(292mm)
(21mm)
A04037
NOTES:
1. Two additional 7/8 ---in. (22 mm) diameter holes are located in the top plate.
2. Minimum return--- air openings at furnace, based on metal duct. If flex duct is used, see flex duct manufacturer’s recommendations for equivalent diameters.
a. For 800 CFM---16--- in. (406 mm) ro und or 14 1/2 x 12---in. (368 x 305 mm) rectangle.
b. For 1200 C FM ---20 ---in. (508 mm) rou nd or 14 1/ 2 x 19 1/2 ---in. (368 x 495 mm) rectangle.
c. For 1600 C FM ---22 ---in. (559 mm) rou nd or 14 1/ 2 x 22 1/16 ---in. (368 x 560mm) rectangle.
d. For airflow r equiremen ts above 1800 CFM, see Air Delivery table in Product Data l iterature for specific use of single side inlets. The use of both sideinlets,a
combination o f 1 side and the bottom, or the bottom only will ensure adequate return air openings for airflow requirements above 1800 CFM.
Fig. 3 -- Dimensional Drawing
Table 1 – Dimensions -- In. (mm)
FURNACE SIZE
A
CABINET
WIDTH
IN. (mm)
D
SUPPLY ---
AIR WIDTH
IN. (mm)
E
RETURN ---
AIR WIDTH
IN. (mm)
F
CENTER LINE TOP AND
BOTTOM FLUE COLLAR
IN. (mm)
FLUE
COLLAR*
IN. (mm)
SHIP WT.
LB (KG)
FIL TER MEDIA
CABINET SIZE
IN. (mm)
070--- 12/ 036070
14--- 3/ 16
(360)
12--- 9/ 16
(319)
12--- 11/ 16
(322)
9--- 5/ 16 (237) 4 (102) 127 (58) 16 (406)
090--- 16/ 048090 17 ---1/2 (445)
15--- 7/ 8
(403)
16 (406) 11--- 9/ 16 (294) 4 (102) 151 (68) 16 (406)
110--- 20/ 060110 21 (533)
19--- 3/ 8
(492)
19--- 1/ 2 (495) 13--- 5/ 16 (338) 4 (102) 163 (74) 20 (508)
135--- 22/ 066135 24 ---1/2 (622)
22--- 7/ 8
(581)
23 (584) 15--- 1/ 16 (383) 4 (102)† 177 (80) 24 (610)
155--- 22/ 066155 24 ---1/2 (622)
22--- 7/ 8
(581)
23 (584) 15--- 1/ 16 (383) 4 (102)† 183 (83) 24 (610)
*5 in. or 6 in. (127 or 152 mm) vent connector may be required in some cases.
{5 in. (127 mm) or larger vent is required. U se a 4 ---5 (102---127 mm) or 4 ---6 (102---152 mm) in. ven t adapter between furnace and ven t connector.
4. If you touch ungrounded objects (and recharge your body
with static electricity), firmly touch a clean, unpainted
metal surface of the furnace again before touching control
or wires.
5. Use this procedure for installed and uninstalled (ungroun-
ded) furnaces.
6. Before removing a new control from its container, dis-
charge your body’s electrostatic charge to ground to pro-
tect the control from damage. If the control is to be in-
stalled in a furnace, follow items 1 through 4 before
bringing the control or yourself in contact with the fur-
nace. Put all used and new controls into containers before
touching ungrounded objects.
7. An ESD service kit (available from commercial sources)
mayalsobeusedtopreventESDdamage.
LOCATION
GENERAL
This multipoise furnace is shipped in packaged configuration.
Some assembly and modifications are required when used in any
of the four applications shown in Fig. 4.
NOTE: For high--altitude installations, the high--altitude
conversion kit MUST be installed at or above 5500 ft. (1676 M)
above sea level. Obtain high--altitude conversion kit from your
area authorized distributor.
58CV
To Next Page
Loading...