109
HARDWARE (cont)
IO DI01 FUNCTION Assigned S-DI01 Function
0=None,
1=COFS,
2=REMOCC,
3=REMOFF,
4=FILTER,
5=ENTHALPY,
6=GEN STAT
SIODI01F
RELAY 06 FUNCTION Assigned Rly 06 Function
0=None,
1=ALM Relay,
2=PE1,
3=PE2
MBBRY06F
RELAY 11 FUNCTION Assigned Rly 11 Function
0=None,
1=ALM Relay,
2=PE1,
3=PE2
MBBRY11F
MBB PART # MBB Part Number CEPL131117-xx-R BD_CEPL
MBB PP MBB Program Part Number CEPP130644-xx-xx-xx-R BD_CEPP
MBB SERIAL # Base Board Serial Number xxxxNxxxxxx BD_SER
CALIBRATION Calibration Menu
OAT TRIMOFFSET OAT Sensor Trim Offset –10.0 to 10.0 °F Configurable OAT_TRIM
RAT TRIM OFFSET RAT Sensor Trim Offset –30.0 to 30.0 °F Configurable RAT_TRIM
FST TRIM OFFSET FST Sensor Trim Offset –10.0 to 10.0 °F Configurable FST_TRIM
SPT TRIMOFFSET SPT Sensor Trim Offset –30.0 to 30.0 °F Configurable SPT_TRIM
SLIDER SEN. TRIM SPTO Sensor Offset Trim –1.0 to 1.0 °F Configurable SPTOTRIM
SPRH TRIM OFFSET SPRH Sensor Offset Trim –15 to 15 % Configurable SPRHTRIM
IAQ TRIM OFFSET IAQ Sensor Trim Offset –200 to 200 ppm Configurable IAQ_TRIM
OAQ TRIM OFFSET OAQ Sensor Trim Offset –200 to 200 ppm Configurable OAQ_TRIM
OARH TRIM OFFSET OARH Sensor Trim Offset –15 to 15 % Configurable OARHTRIM
RARH TRIM OFFSET RARH Sensor Trim Offset –15 to 15 % Configurable RARHTRIM
CIR.A SSP TRIM Cir.A SSP Sensor Trim –50 to 50 psig Configurable SSPATRIM
CIR.A SDP TRIM Cir.A SDP Sensor Trim –50 to 50 psig Configurable SDPATRIM
ECO FEEDBACK TRIM Econ Fdback Trim Offset –15 to 15 % Configurable EC1DTRIM
OACFM TRIMOFFSET OACFM Sensor Trim Offset –10 to 10 CFM Configurable OCFMTRIM
COMMISSION REPORTS Commission Report Menu
SYSTEM STARTUP CHECKLIST
SYSTEM STARTUP CHECKLIST
MENU
QUICK SET CHKLIST QUICK SETUP CHECKLIST
0=Undone,
1=Perfom,
2=Done
Configurable CHK_QUIK
NETWORK CHKLIST NETWORK SETUP CHECKLIST
0=Undone,
1=Perfom,
2=Done
Configurable CHK_NET
SYSTEM AUTOTEST CheckList Auto Test
0=Undone,
1=Perfom,
2=Done
Configurable CHK_ATST
ADVANCED SERVICE
Advanced Service Restricted
Access Menu
RESTORE DEFAULTS? Restore Factory Defaults Yes/No Command RESFDFLT
EDIT MODEL NUMBER Edit Equip Mod Num Menu
EDIT SER NUMBER Edit Equip Ser Num Menu
CLEAR COMPONENT DATA
RESET COMPONENT DATA
MENU
COMP A1 DATA Reset Compressor A1 Data Yes/No Command CR_A1
COMP A2 DATA Reset Compressor A2 Data Yes/No Command CR_A2
LOADER DATA Reset CompressorALD Data Yes/No Command CR_ALD
ALARM RELAY DATA Reset Alarm Relay Data Yes/No Command CR_ALM
ALARM RESET DATA Reset Alarm Resets Data Yes/No Command CR_ALRST
CCH RELAY DATA Reset CCH1 Relay Data Yes/No Command CR_CCHR1
ECON DAMPER DATA Reset Econ Damper Data Yes/No Command CR_DAMP
FULL LOAD DATA Reset Full Load Data Yes/No Command CR_FLOAD
FREE COOL DATA Reset Free Cooling Data Yes/No Command CR_FREEC
HEAT 1 DATA Reset Heat Stage 1 Data Yes/No Command CR_HTR_1
HEAT 2 DATA Reset Heat Stage 2 Data Yes/No Command CR_HTR_2
IDF RUN DATA Reset Indoor Fan Data Yes/No Command CR_IDF
IDF MAX SPD DATA Reset Max Fan Speed Data Yes/No Command CR_MAXF
ODF1 OUTPUT DATA Reset ODF Spd Sig 1 Data Yes/No Command CR_ODF1
Table D — Service Main Menu Layout (cont)
DISPLAY EXPANDED TEXT VALUES UNITS WRITE STATUS POINT
APPENDIX A — SYSTEMVU™ CONTROLLER DISPLAY
To Next Page
Loading...
