To Next PageTo Next Page
Need help?Do you have a question about the Carrier Aquasnap 30RAP045 and is the answer not in the manual?
General| Brand | Carrier |
|---|---|
| Model | Aquasnap 30RAP045 |
| Category | Air Conditioner |
| Language | English |
Carrier's chiller design offers savings at initial purchase, installation, and years afterward.
Highlights the low-sound AeroAcoustic™ fan's contribution to quiet operation in the workplace.
Details cost savings from operation and efficiency, alongside proven reliability and durability.
Describes the comprehensive chilled water circuit, its components, and the optional integrated hydronic system.
Focuses on cabinet construction and the user-friendly ComfortLink™ controls with diagnostic capabilities.
Highlights reduced footprint and discusses Novation® heat exchanger technology with microchannel coils.
Details options that are installed at the factory during manufacturing.
Lists accessories that are installed on-site after the chiller is delivered.
Provides dimensional drawings for the accessory storage tank for specific unit sizes.
Provides dimensional drawings for the accessory storage tank for specific unit sizes.
Provides dimensional drawings for the accessory storage tank for specific unit sizes.
Details pump impeller sizes and option codes for various unit sizes and pump configurations.
Presents charts showing water pressure drop vs. flow rate for different unit sizes in English units.
Presents charts showing water pressure drop vs. flow rate for different unit sizes in SI units.
Charts showing unit pressure drop vs. flow rate for units without a hydronic package in English units.
Charts showing unit pressure drop vs. flow rate for units without a hydronic package in SI units.
Charts showing unit pressure drop vs. flow rate for units with a single pump hydronic package in English units.
Charts showing unit pressure drop vs. flow rate for units with a single pump hydronic package in SI units.
Charts showing unit pressure drop vs. flow rate for units with a dual pump hydronic package in English units.
Charts showing unit pressure drop vs. flow rate for units with a dual pump hydronic package in SI units.
Illustrates typical piping and wiring for units without the hydronic package.
Illustrates typical piping and wiring for size 060 units without the hydronic package.
Illustrates typical piping and wiring for sizes 070-090 without the hydronic package.
Shows a detailed piping diagram for units with the hydronic package.
Electrical specifications for units without a hydronic package, across various fan and power configurations.
Electrical specifications for units with a single point hydronic package and various fan options.
Electrical specifications for units with a dual point hydronic package and optional value sound fans.
Electrical data for fan motors based on single point power supply, standard and optional.
Provides full load ampere ratings for pump motors based on unit size and HP.
Details wiring size requirements for incoming power based on MOCP value and SCCR.
Details microprocessor functions, sensors, start-up, off-cycle, and capacity control logic.
Covers standard capacity steps, dual chiller control, ComfortLink, Navigator, and overrides.
Details safety features, abnormal conditions, temperature reset options, and accessory controls.
Covers default settings, ice duty operation, and configuration considerations for the chiller.
Guidelines for chiller placement, clearances, oversizing, multiple units, and pump control.
Details cooler temperature, flow rates, strainers, and water system cleaning/quality.
Covers variable speed pumping, air separation, fluid loop volume, and bypass flow.
Addresses fluid volume, freeze protection, ambient limits, and utility interests.
Covers minimum/maximum flow rates, high/low ambient operation, and altitude correction factors.
Discusses closed-loop water systems, installation practices, and potential issues.
Details water system cleaning procedures, water quality limits, and condenser coil protection options.
Focuses on energy management practices like demand limiting and temperature reset.
Covers remote control, hydronic systems, and essential air separation techniques for water loops.
Covers system description, quality assurance, and delivery/storage/handling requirements.
Details general equipment, unit cabinet, fans, compressor, cooler, and condenser specifications.
Details refrigeration components, safeties, diagnostics, and control functions.
Covers electrical requirements, chilled water circuit, and hydronic package specifications.
Details VFD systems, bypass, EMM, security, vibration, communication, and special features.
Covers freeze protection, fans, sound reduction, SCCR, service valves, digital compressors, and accessories.
