6
WiFi B--SAM SETUP 1
AUX: AUX SENSOR
IP TYPE: DHCP
IP: 192.168.100.0
MAC ADDR:
00:01:02:03:04:05
SUBNET MASK:
255.255.255.000
SERVER
STATUS: CONNECTED
<BACK NEXT >
WiFi B--SAM SETUP 2
DEFAULT GATEWAY:
192.168.001.001
DNS SERVER:
061.010.231.015
PORT: 49152
SERVER
STATUS: CONNECTED
<BACK NEXT >
AUX: The auxiliary sensor can be renamed to something meaningful, such as WATER or GENERATOR. Use the Temp +/-- buttons to move
between letters, and the Time +/-- button to choose letters.
IP TYPE: Choose DHCP (default) or STATIC for the Internet addressing type.
IP: Shows the current IP address of the WiFi B--SAM. If IP TYPE is STATIC then this item can be change. Use the Temp +/-- buttons to
move between letters, and the Time +/-- button to choose letters. If IP TYPE is DHCP, the IP address cannot be changed.
MAC ADDR: Shows the MAC Address of the WiFi B--SAM’s network module.
SUBNET MASK: If IP TYPE is STATIC, this can be changed to a different subnet number. Use the Temp +/-- buttons to move between
letters, and the Time +/-- button to choose letters. If IP TYPE is DHCP, the SUBNET MASK cannot be changed.
DEFAULT GATEWAY: If IP TYPE is STATIC, this can be changed to point to a different gateway. Use the Temp +/-- buttons to move
between letters, and the Time +/-- button to choose letters. If IP TYPE is DHCP, the DEFAULT GATEWAY cannot be changed.
DNS SERVER: If IP TYPE is STATIC, this can be changed to point to a different DNS server. Use the Temp +/-- buttons to move between
letters, and the Time +/-- button to choose letters. If IP TYPE is DHCP, the DNS SERVER cannot be changed.
PORT: This can be changed to use a different port through the homeowner’s network. The default is port 49152.
SERVER STATUS: Shows status of the WiFi B--SAM connection to Carrier’s servers. If the screen shows NON CONNECTED, please
check network settings or network cable.
Pressing the right side button (for NEXT >) will display the following screen:
WiFi B--SAM WIRELESS 1
SSID:
HOME
CHANNEL: 0
SIGNAL STRENGTH:
JJJjjjjjj
L H
SERVER STATUS: CONNECTED
<BACK NEXT >
WiFi B--SAM WIRELESS 2
ENCRYPTION:
WEP 64 BIT HEX
KEY:
ENTER 10 HEX DIGITS
0--9, A--F
<BACK NEXT >
SSID: Enter the name of the homeowner’s wireless network using the Temp +/-- and Time +/-- buttons.
CHANNEL: This field determines which frequency to use. It can be left on Channel 0 to search automatically, or adjusted to the one being
used by the homeowner’s wireless router.
ENCRYPTION: This chooses the type of security used by the homeowner’s wireless router. Choose:
S None -- no data encryption
S WEP (Wired Equivalent Privacy) -- use WEP 64 or 128 bit data encryption
S WPA (Wi--Fi Protected Access Pre--Shared Key ) -- use WPA--PSK standard encryption
KEY: WEP 64 BIT HEX (10 hex digits)
WEP 64 BIT CHARS (5 ASCII characters)
WEP 128 BIT HEX (26 hex digits)
WEP 128 BIT CHARS (13 ASCII characters)
WPAPSKHEX(8to64hexdigits)
WPA PSK CHARS (8 to 63 ASCII characters)
SIGNAL STRENGTH: Displays the current signal strength of the identified wireless router (SSID). Nine bars is full strength.
CONNECTED means the WiFi B--SAM has connected with the wireless router. NOT CONNECTED will mean either one of the parameters
is incorrect, or the signal strength may be too low.
Copyright 2012 Carrier Corp. S 7310 W. Morris St. S Indianapolis, IN 46231 Printed in U.S.A. Edition Date: 02/12
Manufacturer reserves the r ight to change, at any ti me, specifications and designs without notice and without obligations.
Catalog No: CCRWF---02SI
Replaces: CCR W F ---01SI
SYSTXCCRWF01
To Previous Page
Loading...
