Carrier Omnizone 50BV020-064

Questions and Answers

R
Ryan JacksonAug 7, 2025
What to do if my Carrier Omnizone 50BV020-064 Chiller unit will not start?
- T
  twareAug 7, 2025
  If your Carrier Chiller unit won't start, begin by checking the power source, fuses, circuit breakers, and disconnect switch. Inspect electrical contacts for any issues. Ensure the unit voltage is correct and address any discrepancies. Look for open fuses and check for short circuits within the unit. Examine relays, contacts, and pressure switches for any open protection devices. Finally, test the unit or motor contactor and replace it if necessary.
P
Patrick JacksonAug 11, 2025
Why is my Carrier Omnizone 50BV020-064 compressor noisy but won't start?
- J
  Jason PowersAug 11, 2025
  If your Carrier Chiller's compressor is noisy but refuses to start, the issue might stem from several causes. First, check for undervoltage and correct it if necessary. A defect in the compressor motor could also be the culprit, requiring a compressor replacement. Additionally, verify that all phases are present and correct any missing ones. Lastly, the compressor might be seized, in which case you should check it and replace it if necessary.
P
Philip KingAug 15, 2025
What should I do if my Carrier Chiller has high discharge pressure?
- S
  Scott JenkinsAug 16, 2025
  If your Carrier Chiller is experiencing high discharge pressure, start by checking for low water flow in the condenser and purge any air present. Inspect and clean the condenser tubes if they are dirty. Also, check the water tower fans and pumps if the condenser water temperature is high. If the system is overcharged, check and reclaim any excess charge and adjust the subcooling. Finally, verify and correct any non-condensing gas present.
D
Dana CarsonAug 20, 2025
What to do if my Carrier Omnizone 50BV020-064 Chiller compressor starts, but does not continue to run?
- K
  Kyle SantiagoAug 20, 2025
  If the compressor in your Carrier Chiller starts but doesn't continue running, check for a defect in the compressor or contactor and replace if necessary. The unit might be undercharged, so check for leaks, correct them, and add refrigerant. Consider if the unit is too big by checking the load calculation. The compressor may be overloaded; inspect and replace the protection device, check for a missing phase, check the TXV, and check the temperature in the suction discharge line.
J
jgreenAug 29, 2025
Why is my Carrier Omnizone 50BV020-064 unit so noisy?
- R
  Rick CallahanAug 29, 2025
  If your Carrier Chiller unit is making excessive noise, there are several potential causes. It could be compressor noise, so check the TXV and replace it if necessary, ensure the compressor rotation is correct, and check for internal noise. Tube vibration or a condenser water problem could also be responsible, so check and correct these issues. Additionally, a unit panel or part may be vibrating; check and tighten the appropriate part.
C
Christopher LeblancSep 1, 2025
What to do if the fan on my Carrier Omnizone 50BV020-064 does not operate?
- M
  michaelandrewsSep 1, 2025
  If the fan on your Carrier Chiller isn't working, start by checking the contactor or relay for overloads or defects, and replace if necessary. Confirm that the VFD parameters are correctly set if a VFD is used. Test the motor and replace it if it's defective. Inspect the belt for breakage and replace it if needed. Finally, ensure all electrical contacts are tight.
A
Andrew DayNov 23, 2025
How to troubleshoot a Carrier Omnizone 50BV020-064 Chiller unit that runs continuously but has low capacity?
- T
  Taylor FlemingNov 23, 2025
  If your Carrier Chiller runs continuously with low capacity, several factors could be responsible. First, verify the unit isn't undersized by checking the load calculation. Next, inspect for low refrigerant levels or the presence of non-condensing gas, addressing any leaks and replenishing refrigerant or gas as required. A defective compressor might be the cause; check its pressure and amps, replacing it if necessary. Insufficient refrigerant flow in the evaporator could also be at fault; check the filter drier (replace if needed), TXV (adjust or replace if needed), and the position of the TXV bulb and equalizer. Oil in the evaporator can impede performance, so drain it. Lastly, investigate low airflow by checking filters (clean or replace), coils (clean), ductwork (check for restrictions)...