Carrier RG56N Series - Advanced Remote Functions

Follow Me
Fresh
HOW TO USE ADVANCED FUNCTIONS
08
07
Direct
Press Direct button
The horizontal louver will move an angle of 6 degree for each press.
Press the button until the louver reach your prefer location.
Follow Me
Fresh
Sleep
Swing
Press Swing button
The horizontal louver will swing up and down
automatically when pressing Swing button.
Press again to make it stop.
Press Swing button for more than 2 sec
Keep pressing this button more than 2 seconds, the vertical
louver swing function is activated. (Model dependent)
2s
Sleep
Press Sleep button (RG56N) under Cool/Heat mode
This Sleep operation saves energy and improves night time comfort by synchronising with the
body’s metabolism.
Follow
Me
or
Fresh
Press this button under COOL or HEAT operating Mode
Press this button to activate Follow me. This function
can adjust room temperature base on the controller’s
sensor and make you comfort.
Press this button more than 2 seconds
Keep pressing this button more than 2 seconds, the
fresh function is activated and will help to remove
pollen and impurities from the air. (Model dependent)
2s
The controller will display
the actual temp. at its
location and send this
signal to indoor unit
every 3 minutes
The ionizer or Plasma
dust collector (model
dependent) is energized.
LED
Self Clean
LED
Self Clean
LED
or
Self
Clean
Press LED button
Press this button to turn on and turn off the display
on the indoor unit.
Press this button under COOL or DRY Mode more than 2 seconds
Keep pressing this button more than 2 seconds, the unit will
clean itself to avoid bacteria grow around heat
Cl dependent)
2s
The unit will enter low
fan mode to dry up the
coil. The cleaning cycle
takes 15~30 mins, after
which the unit will turn
off automatically.
Turbo
Silence
Turbo
Silence
Turbo
or
Silence
Press this button
Press this button to activate Turbo. It enables
the unit to reach the set temperature in
the shortest time. Press it again to disable it.
Press this button more than 2 seconds
Keep pressing this button more than 2 seconds, the Silence
function is activated. (Model dependent)
Note: Due to low speed of operation, it may result in
insufficient cooling and heating capacity.
2s
The unit will operate at the
biggest capacity outut to
reach the setting Temp. quickly.
The unit will bring faint
breeze to reduce the
noise to the lowest level .
My Mode
My Mode
My
Mode
Press this button
My mode function enable you to memorize or restore your favorite settings (mode, temperature and fan
speed). The default memorized setting is AUTO mode, 26 C and AUTO fan.
Press this button more than 2 seconds
In AUTO mode for heat pump system, the air conditioner can automatically choose the mode of Cool, Heat, Fan
by sensing the difference between the actual room temperature and setting temperature.
2s
The unit will restore to
the setting you made
last time.
The unit will memorize
the current setting
mode, Temp., fan).
The set temp. will increase
(cooling) or decrease
(heating) by 1 C per hour
for the first 2hs. Thereafter
it keeps this new temp. for
5hs before switching off.
X-ECO
X-ECO
or
Sleep
Press more than 2 seconds under Cool/Heat operate mode for Sleep
This X-ECO and Sleep operation saves energy and improves night time comfort by synchronising with the
body’s metabolism.
The set temp. will increase
(cooling) or decrease
(heating) by 1 C per hour
for the first 2hs. Thereafter
it keeps this new temp. for
5hs before switching off.
X-ECO
Press X-ECO button (RG56V) under Cool mode
The unit will automatically
regular the fan speed and
compressor speed. The
temp. can be selected from
24~30 C in ECO mode.
The function will be disable
after 8hs.
2s
Note:Please put the controller in the location where
can ensure the indoor unit can receive the signal.
Note: The X-ECO function is invalid for multi system.