Casablanca 99019 - User Manual

To Next Page

www.CasablancaFanCo.com

1.888.227.2178

M6009-01 • 04/17/14 • © Casablanca Fan Company

Model 99019

Universal

Remote Control

Transmitter &

Receiver

Installation

Wiring

OR OR OR

OFF

Remove the canopy. If uncertain

how to remove it, reference the fan’s

owner’s manual. With wiring exposed,

it may be helpful to note existing wire

connections or take a digital photo for

reference. Remove the wire connectors

that were connecting the wires from

the outlet box to the fan, leaving the

grounding wires connected.

CONNECT WIRES FROM RECEIVER TO FAN -Using the blue wire connectors connect the white wire from the

receiver (marked “common out”) to the white wire from fan. Connect the black wire from the receiver (marked

“fan out”) to the black wire from the fan. Connect the blue wire from the receiver (marked ”light out”) to the

blue wire (or possibly black with white stripe) from the fan.

Note: The red wire from the receiver has a pre-installed wire terminator. It is for fans with an optional up light;

otherwise it will not be used. Maximum 120 watts.

If you’re uncertain about wire colors or connections, please contact a qualied electrician.

CONNECT WIRES FROM RECEIVER TO WIRES FROM OUTLET BOX - Using an orange wire connector connect

the black wire (ungrounded) from the ceiling to the black wire from the receiver (marked “live in”). Connect

the white wire (grounded) from the ceiling to the white wire from the receiver (marked “neutral in”).

AFTER ALL WIRES ARE CONNECTED and secured with wire connectors, re-install the canopy.

Before installing the Universal Remote

Control Receiver, use the pull chains to

set the fan speed to HIGH and the light

to ON. Be sure power is OFF before

proceeding with installation.

Choose the hanging system that most closely resembles the one used by your fan and install the receiver and wire as directed.

Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”. Place remaining excess

wire into the ceiling electrical box. The bracket and fan must remain properly grounded.

This Remote Control Transmitter and Receiver is not compatible with Casablanca Hang Tru® Canopy Systems.

You may have installation issues if the fan is installed on an angled ceiling.

Ceiling

Plate

Receive

Canopy

Receiver

Canopy

Ceiling

Bracket

Receiver

Fan Body

Cable Tie

For low prole fans, the receiver should

be secured to the ceiling bracket with a

cable tie.

Receiver

Canopy

Turn the splices upward and push them carefully back through the hanger bracket

into the outlet box. Spread the wires apart, with the grounded wires on one side of the

outlet box and the ungrounded wires on the other side of the outlet box.

To avoid possible electrical shock, before installing or servicing your fan, disconnect

the power by turning off the circuit breakers to the outlet box and associated wall

switch location. If you cannot lock the circuit breakers in the off position, securely

fasten a prominent warning device, such as a tag, to the service panel.

black (ungrounded)

white (grounded) white (neutral in)

black (live in)

white

black

blue

white (common out)

black (fan out)

blue (light out)

If you are installing multiple remote-controlled fans

on the same circuit breaker,

you may need to perform a few extra steps to prevent

interference or faulty operation of your remote controls.

Go to www.HunterFan.com/FAQs and click “How do I properly

install multiple remote-controlled fans?” for more information.

Need help?

Do you have a question about the Casablanca 99019 and is the answer not in the manual?

Casablanca 99019 Specifications

General

Brand	Casablanca
Model	99019
Compatibility	Casablanca Ceiling Fans
Battery Quantity	2
Type	Remote Control
Control Type	Wireless
Functions	Fan Speed Control, Light Dimming