Case 885 Diesel User Manual

SHOP MANUAL
CASE/INTERNATIONAL
MODELS
385—485—585—685—885
Engine serial number is stamped on right side of
engine crankcase on all models. Tractor model and
serial number are stamped on a plate attached to
right side of front axle support. Transmission serial
number is stamped on a plate attached to the right
rear side of rear main frame. Model and serial num-
ber plate for front drive axle is located on left rear
of axle housing.
INDEX (By Starling Paragraph)
BRAKES
At^ustment
Bleed
Master Cylinders
R&R and Overhaul
CLUTCH, ENGINE
Adjustment
Cylinders
R&R and Overhaul
CAB
Remove and Reinstall...
COOLING SYSTEM
Pan
Radiator
Water Pump
DIESEL FXTEL SYSTEM
Ether Starting Aid
Filters and Bleeding
Iiyection Pump
Nozzles
385
Diesel
121
122
124
123
97
101
69
68
71
67
60
61
64
485
Die8el
121
122
124
123
97
101
69
68
71
67
60
61
64
585
Diesel
121
122
124
123
97,98
99
101
145
69
68
71
67
60
61
64
685
Diesel
121
122
124
123
97,98
99
101
145
69
68
71
67
60
61
64
885
Diesel
121
122
124
123
97,98
99
101
145
69
68
71
67
60
61
64
www.maskinisten.net

Case 885 Diesel Specifications

General

Type	Tractor
Engine	Diesel
Fuel Capacity	24.5 gal
Engine Model	Case IH
Engine Power (Max)	80 hp
Displacement	239 ci
Cylinders	4
Transmission Type	Synchro
PTO Power	65 hp
Hydraulic Flow	15 gpm
Fuel Tank Capacity	24.5 gal
Weight (Approx)	6, 800 lbs
Length	148 inches
Width	84 inches
Height (to exhaust)	108 inches

Summary

FRONT AXLE (TWO-WHEEL DRIVE)

SPINDLES

Procedure for removing, inspecting, and reinstalling spindles on adjustable axles.

FRONT-WHEEL DRIVE

DRIVE AXLE ASSEMBLY AND FRONT SUPPORT

Steps for removing and reinstalling the front drive axle assembly and its support.

SWIVEL HOUSING AND AXLE SHAFT

DIFFERENTIAL AND BEVEL DRIVE GEARS

FRONT DRIVE SHAFT AND SHIELD

POWER STEERING SYSTEM

HYDROSTATIC STEERING TESTS

PRIORITY FLOW DIVIDER

Procedure for checking the flow divider valve and its operation.

STEERING HAND PUMP

Procedure for removing, overhauling, and testing the steering hand pump.

HYDRAULIC PUMP

PRIORITY FLOW DIVIDER

STEERING HAND PUMP

STEERING CYLINDER

CYLINDER AND VALVE UNIT

ENGINE AND COMPONENTS

R&R ENGINE ASSEMBLY

Procedure for removing and reinstalling the engine assembly from the tractor.

VALVES AND SEATS

TIMING GEARS

ROD AND PISTON UNITS

PISTONS, SLEEVES AND RINGS

CRANKSHAFT AND MAIN BEARINGS

OIL PUMP AND RELIEF VALVE

DIESEL FUEL SYSTEM

INJECTION PUMP

INJECTION PUMP CONTROL ADJUSTMENTS

INJECTION NOZZLES

ELECTRICAL SYSTEM

CHARGING SYSTEM

ALTERNATOR

Information on Lucas alternators, including specifications and testing procedures.

ALTERNATOR

STARTING MOTOR

CLUTCH

ADJUSTMENT

Clutch linkage adjustments for models without cab.

CLUTCH CYLINDERS

R&R AND OVERHAUL CLUTCH

TWO SPEED POWER SHIFT

REGULATOR (CONTROL) VALVE

Procedure for removing and overhauling the regulator valve.

POWER SHIFT UNIT

FORWARD-REVERSE TRANSMISSION

REGULATOR VALVE

FORWARD-REVERSE UNIT

SYNCHROMESH SPEED TRANSMISSION

SPEED GEARBOX

RANGE TRANSMISSION

R&R AND OVERHAUL

MAIN DRIVE BEVEL GEARS AND DIFFERENTIAL

R&R AND OVERHAUL DIFFERENTIAL

Procedure for removing and overhauling the differential assembly.

DIFFERENTIAL LOCK

PARK BRAKE

FINAL DRIVE

BRAKES

BRAKE ADJUSTMENT

BRAKE ASSEMBLIES

BRAKE MASTER CYLINDERS

POWER TAKE OFF

OPERATING PRESSURE TEST

PTO CLUTCH, SHAFTS AND GEARS

HYDRAULIC LIFT SYSTEM

TROUBLE SHOOTING

TEST AND ADJUST

RELIEF VALVE AND FLOW DIVIDER

HITCH ADJUSTMENTS

UNLOADING AND FLOW CONTROL VALVE

HYDRAULIC LIFT HOUSING

FILTER, FLUID AND PUMP

AUXILIARY CONTROL VALVE