Case 385 Diesel User Manual

SHOP MANUAL
CASE/INTERNATIONAL
MODELS
385—485—585—685—885
Engine serial number is stamped on right side of
engine crankcase on all models. Tractor model and
serial number are stamped on a plate attached to
right side of front axle support. Transmission serial
number is stamped on a plate attached to the right
rear side of rear main frame. Model and serial num-
ber plate for front drive axle is located on left rear
of axle housing.
INDEX (By Starling Paragraph)
BRAKES
At^ustment
Bleed
Master Cylinders
R&R and Overhaul
CLUTCH, ENGINE
Adjustment
Cylinders
R&R and Overhaul
CAB
Remove and Reinstall...
COOLING SYSTEM
Pan
Radiator
Water Pump
DIESEL FXTEL SYSTEM
Ether Starting Aid
Filters and Bleeding
Iiyection Pump
Nozzles
385
Diesel
121
122
124
123
97
101
69
68
71
67
60
61
64
485
Die8el
121
122
124
123
97
101
69
68
71
67
60
61
64
585
Diesel
121
122
124
123
97,98
99
101
145
69
68
71
67
60
61
64
685
Diesel
121
122
124
123
97,98
99
101
145
69
68
71
67
60
61
64
885
Diesel
121
122
124
123
97,98
99
101
145
69
68
71
67
60
61
64
www.maskinisten.net

Case 385 Diesel Specifications

General

Engine Type	Diesel
Type	Utility tractor
Cylinders	4
Hydraulic System	Open center
Transmission	8-speed

Summary

BRAKES

BRAKE ADJUSTMENT

CLUTCH, ENGINE

COOLING SYSTEM

WATER PUMP

DIESEL FUEL SYSTEM

Filters and Bleeding

Procedures for maintaining fuel filters and bleeding the system.

FILTERS AND BLEEDING

DIFFERENTIAL LOCK

R&R and Overhaul

Procedures for removing, installing, and overhauling the differential lock.

ELECTRICAL SYSTEM

Starting Motor

ENGINE

Assembly, R&R

Procedures for engine assembly and removal/installation.

Crankshaft and Main Bearings

Procedures for crankshaft and main bearing service.

Pistons, Sleeves and Rings

Procedures for servicing pistons, sleeves, and rings.

FINAL DRIVE

Assemblies, R&R

Procedures for removal and installation of final drive assemblies.

FRONT SYSTEM (Two-Wheel Drive)

Tie Rods and Toe-In

FRONT AXLE (TWO-WHEEL DRIVE)

FRONT WHEEL BEARING

Procedures for servicing front wheel bearings.

SPINDLES

SWIVEL HOUSING AND AXLE SHAFT

DIFFERENTIAL AND BEVEL DRIVE GEARS

FRONT DRIVE SHAFT AND SHIELD

TRANSFER GEARBOX

POWER STEERING SYSTEM

STEERING CIRCUITS

LUBRICATION AND BLEEDING

Procedures for lubricating and bleeding the power steering system.

HYDROSTATIC STEERING TESTS

STEERING CYLINDER

ENGINE AND COMPONENTS

R&R ENGINE ASSEMBLY

Procedures for engine assembly removal and installation.

CYLINDER HEAD

NOZZLE SLEEVES

VALVES AND SEATS

TIMING GEARS

CAMSHAFT AND BEARINGS

ROD AND PISTON UNITS

PISTONS, SLEEVES AND RINGS

PISTON PINS

CONNECTING RODS AND BEARINGS

CRANKSHAFT AND MAIN BEARINGS

CRANKSHAFT SEALS

ENGINE BALANCER

INJECTION PUMP

INJECTION PUMP CONTROL ADJUSTMENTS

INJECTION NOZZLES

CHARGING SYSTEM

ALTERNATOR

STARTING MOTOR

CLUTCH

ADJUSTMENT

R&R AND OVERHAUL CLUTCH

TWO SPEED POWER SHIFT

REGULATOR (CONTROL) VALVE

POWER SHIFT UNIT

FORWARD-REVERSE TRANSMISSION

PRESSURE TEST AND ADJUST

FORWARD-REVERSE UNIT

SYNCHROMESH SPEED TRANSMISSION

RANGE TRANSMISSION

R&R AND OVERHAUL

MAIN DRIVE BEVEL GEARS AND DIFFERENTIAL

R&R AND OVERHAUL DIFFERENTIAL

DIFFERENTIAL LOCK

PARK BRAKE

All Models

Procedures for park brake adjustment.

OVERHAUL REAR AXLE AND RING GEAR

BRAKE MASTER CYLINDERS

BLEED BRAKES

POWER TAKE OFF

OPERATING PRESSURE TEST

PTO CLUTCH, SHAFTS AND GEARS

HYDRAULIC LIFT SYSTEM

TROUBLE SHOOTING

Troubleshooting common hydraulic lift system symptoms.

TEST AND ADJUST

Procedures for testing and adjusting the hydraulic system.

RELIEF VALVE AND FLOW DIVIDER

HITCH ADJUSTMENTS

UNLOADING AND FLOW CONTROL VALVE

HYDRAULIC LIFT HOUSING

CYLINDER AND VALVE UNIT

FILTER, FLUID AND PUMP