Casio Celviano AP-65R User Manual

tNOTESE
+
The
intasnal
channels
cantroilec
by
the
ntarnal
mode
are
completely
different
trom
the
external
channels
controlled
by
the
exterral
mada
This
moans
thal
there
are
a
total
of
92
different
chanels,
The
Mixer
mode
saves
internal
mode
and
External
Mode
parameters
separately
trom
each
other.
+
The
External
Made
is
tor
MIDI
(ar
SMF
playback*).
See
"MIDI"
on
page
E.71
for
information
about
how
tha
Mixer
is
sed
during
MIO!
opera-
tions.
+ SME Playback
‘The
built-in
disk
drive
of
the
piano
allows
playback
of
SMF
(stan-
dard
MID
files)
from
diskette.
See
“Lsing
the
Floppy
Disk
Drive”
‘on page E-63 for details.
To select the Mixer mode
Press
the
MIXER
SELECT
button
to
toggle
between
the
Mixer
node
sub-modes
as
shown
in
the
illustration
below.
The
currently
selected
mode
is indicated
on the
display.
INTERNAL
= a
a
tnternat
Se
BF
ixiema
exteAwaL
KO
Turning
Channels
On
and
Off
Press
the
CHANNEL
buttons
ta
toggle
individual
channels
on
ard
uff, Indicators
on the display
show the current
on/off
status
of each
channel,
eee
wae
2
ee
oe
a
ee
ee
SN
AS
ED
Chanwel
on
Ghaonet
ott
The
channel
affected
and
the
operation
performed
when
a
CHAN-
NEL
button
is
pressed
depends
or
what
Mixer
mode
yau
are
in,
as
described
below.
E-40
internal Mode
*
Each
press
of
a
CHANNEL
button
toggles
the
applicable
channel
‘on and off.
‘The
on/off
status
of
each
channel
determines
the
on/off
status
of
the
corresponding
part
for
keyboard
play,
Auto
Accompaniment,
and Song Sequencer playback.
+
Changing
to
a
different
rhythm
causes
Mixer
Settings
tor
CHS
through
CH10
to
change
to
the
default
settings
assigned
to
the
new
thythmn.
These
settings
also
change
to
the
defaults
for
the
currentiy
selected
rhythm
pattern
whenever
you
switch
between
th
Normal,
Variation,
Fill-in,
and
Ending
patterns,
£xternal Mode
On/otf
settings
in
this
mode
alfect
MIDI
input
and
SMF
playback
channels.
*
In
the
External
Mode,
each
press
of
CHANNEL
button
CHI
through
CHI6
toggles
the
applicable
channel
on
and
off.
Changing
the
Parameters
of
a
Channel
Use
the
following
procedure
to
change
the
parameters
of
each
indt-
vidual
channel.
To
change
channel
parameters
1.
Press
the
ENTER
button.
2.
Press
the
MIXER
SELECT
button
to
select
the
Mixer
mode
you
want
to
use
*
Select
the
internal
mode
to
make
layer,
split.
Auto
Accompa
sient,
or
Sang
Sequencer
settings.
*
Select
the
External
Mode
to
make
MIDI
settings.
3. Use the [4] and [pb] CURSOR keys to select the
channel whose parameters you want to change.
= See page E 39 for details on layer, split, Auto Accompani-
ment, and Song Sequencer channel assignments.
* The frame around the currently selected channel (the cur-
rent channel) flashes. to indicate that it is selected.
ybitie
[=—— Cnannei rumver frame
TTTTEN
« The on/cff status of the current channel is indicated in the
measure number area of the display (item 12 on page E-14).
on...
OFF
4. Change the current channel's tone and volume pa
rameters while a channel number frame is flashing, if
you want.
* Use the [+] and [-] buttons to change the tone.
* Use [4] and '¥] to change the volume. The current volume
setting is shown as a value in the metrorome area of the dis
play (iter 6 on page E-14).
-On
VOLUME
mn
uu
To make additional settings for the current cnannel,
press the ENTER button while a channel number frame
is flashing.
+ See “To make additional channel parameter settings” for
details on making additional channel parameters
6. After making additiona’ settings in step 5, press the
ENTER button.
* If you do not perform any operation for about seven sec-
‘onds while a channel number frame is flashing, the display
returns to that in step 2 of the above procedure autamatical-
ly.
INOTES #
* Internal Mode and External Mode settings you make with thi
procedure are stoved separately
+ Youcan change the parameters of @ channel regardiess of whether the
cchannat is on or off
* Changing a Mixar internal mode channel setting causes tne MIDI mas-
‘sage
that
corresponcs
to
the
change
to
be
output
through
the
MiD!
OUT
terminal.
ove
To make additional channel parameter settings
When
making
channel
parameter
settings,
press
the
ENTER
button
to display
the first additional
channe!
parameter
screen,
Use the [4] and [¥] CURSOR keys to scroll through the setting screens
shown below.
While any sethng screen is on the display, use the [+] and (-] buttons
zo change che parameter to the value you want.
{Pare a ‘Screen [Batting Range:
Program Change Number [GOOF r99,No 000-23
295 Volume 60 ~ 127
BGY4Pan 900 ~ 127
OYGEt fect 90 ~ 127
OGFineTune | ~s0-w- s9
a0C.Tune
|
-v-w-2
See the following section titled “Additional Channel Mode Parame
ters” on page E-4? for details on what each of these parameters con-
trols
ENOTES E
+ The tir screen is normally the pan screan. If you usad the additional
channel parametar scraane since turning an powar, the last satling you
rs first.
the {-¢} and {| CURSOR keys to change tho curront chan
nel while an additional channel parametar screen is on the display.
+ Channel 10 is reserved for drum sounds, 80 only lone number 192 to
199 can be selected.
E-41

Casio Celviano AP-65R Specifications

General

Brand	Casio
Model	Celviano AP-65R
Category	Musical Instrument
Language	English