Casio Celviano AP-65R User Manual

Figure 4
4, Kirst, attach (3 clips to the tour locations on back panei €!. Inscall
back panel ® onto the assembly made up of side uprights @ ard
\®),
and
crosspiece
@.
Secure
it
in
place
w:th
four
@
screws
and
four ®) screws, Also install the two © clips and four ® screws
(Figure 4).
*
Make
sure
that
the
rough
surface
of
back
panel
©
is
tacing
to-
wards
the back of the stand.
* Start with the four ® screws on the left and right, and then in-
stall the other four ®) screws. When installing the two screws
marked @ in Figure 4, pass the screws through the holes in the
Oclips and then screw the screws intu place on the stand.
Figure 5
5,
Rotate
height
adjustment
screw
@
until
it
supports
crosspiece
©,
preventing
the
crosspiece
frum
bending
when
you
press
the
ped-
als
(Figure
5),
E-84
ooo IMPORTANT!
Be sure to instell adjustment screw Q> and perform the adjustment
procedure describec abcve before depressing the pedals Failure ty
do so can result in damage to crosspiece ©.
femmes
2
Installing
the
Keyboard
mam
onto
the Stand
_ A Caution
Take
care
that
you
do
not
pinch
your
fingers
between
the
key-
board
and stand!
Figure
6
71
Be sure that you securely anchor the keyboard to the stand using the
@ buttertly bolts (Figure 6)
* Position the keyboard so the two rubber feet on i:s botiom (at the
two back comers) are behind (more towards the back of the stand
than)
the
stand’s
two
rear
angle
brackets
G.
In
this
position,
the
bolt holes in the bottom of the piano will be correctly aligned with
the bolt holes of the stand’s angle brackets.
+ The butterfly bolts keep the keyboard from falling from the stand.
Be
sure
that
you
always
secure
the
keyboard
with
the
butterfly
bolts.
gees El Connecting the Pedal
Figure 7
Pedal
pw9
Position
the
pedal
p'ug
as
shown
in
Figure
7
and
insert
it
into
the
pedal
cunnector
on
the
bottonr
of
the
piano.
Secure
the
pedal
cable
to
the
upright
of
the
stand
using
the
()
clips
that
you
installed
when
assembling
the
stand,
was
EI
Connecting
to
a
Power
Supply
mmm
Household
wall outlet
Powar cond
1.
Check
to
make
sure
thal
the
piano's
POWER
button
is
in
the
OFF
position.
If it is ON, press the button
to switch
it OFF.
2.
Attach
the
power
cord
that
comes
with
the
piano
to
the
back
of
the
piano.
3. Plug the piano’s power cord into a wail outlet (Figure 8)
IMPORTANT!
+
The
shapes
of
the
piano’s
power
cord
and
wail
outlet
shaula
be
different
according
to countries
or regions.
The illustrations
are
examples.
+ With some CELVIANO models, the power cord is hard-wred to the
back of the instrument.
y
3
Hy
i
t
}
j
ZX caution
The screws that you use to assemble the stand may became loose
after a long period due to changes in temperature and humid:-
ly, or vibration caused by normal use, etc. Periodically check
the screws used to fasten the stand and the butterfly bolts used
to fasten the stard and the piano, and tighten them whenever
necessary,
E-85

Casio Celviano AP-65R Specifications

General

Brand	Casio
Model	Celviano AP-65R
Category	Musical Instrument
Language	English