cecotec Conga 7490 Eternal Genesis - Page 29

CONGA 7490 ETERNAL GENESIS CONGA 7490 ETERNAL GENESIS
5756
ENGLISH ENGLISH
Side brush. Fig. 11
The side brush is designed with many bristles and used both to push dirt into the suction
mouth and thoroughly clean edges and corners. This brush may wear out overtime, which will
negatively aect cleaning eciency.
Recommendation
- It is recommended to clean the side brush once a week with the help of the self-
cleaning brush.
- Remove the side brush by pulling it outwards and clean it regularly.
Recommendation
To ensure perfect cleaning, it is recommended to change the side brush every 3 months
(depending on frequency and type of use).
Mixed tank. Fig. 12:
- Remove the mixed tank.
- Open the mixed tank cover and empty it.
- Remove the lter and lter holder as shown in gure 12.
- Use the self-cleaning brush to clean the inside of the mixed tank.
- You can clean the dust compartment with water, without immersing the tank.
- Reinstall the mixed tank on the robot vacuum cleaner.
High-eciency lter. Fig. 13:
- The high-eciency lter is designed with bres that help trap dust particles, dust mites,
pollen... It is very important to periodically clean the lter, to prevent these particles
from building up in the lter, causing eciency loss. It is convenient to carry out this
maintenance once a week.
- Replace the high-eciency lter every 3 months, depending on the frequency and type
of use.
Recommendation
You can remove dirt from the high-eciency lter with a small brush or gently shake the lter
on a hard surface to remove the dust. The high-eciency lter cannot be washed.
Primary mesh lter and sponge lter
The ltering system is featured with a primary mesh lter and a sponge lter, located next to
the high-eciency lter. It is suggested to replace them either after a maximum of 160 hours
of use or when they are worn out due to operation.
Recommendation
Dirt can be removed with a small brush or by shaking carefully against a hard surface for dust
Power Level function:
Select the power level on the app to control the robot vacuum cleaner’s suction power during
cleaning. There are 3 power levels: Turbo, Normal, and Eco.
Cleaning scheduling:
- To make cleaning easier, the robot vacuum cleaner has a function that allows it to be
programmed daily from the app. According to the setting, the robot vacuum cleaner will
automatically start cleaning in the selected days at the desired time.
- Before setting the hour and the options on the robot vacuum cleaner, make sure it is on.
Other functions;
Night functions:
The robot vacuum cleaner can be assigned a do-not-disturb time slot, which can be modied
or cancelled from the mobile APP. During the set time, the robot vacuum cleaner will disable
the automatic, continuous cleaning and timer functions.
Map Editing function:
This function allows you to edit generated maps: rename cleaning areas, split or combine
areas, and edit cleaning mode, suction power, and scrubbing level in each selected area.
Robot vacuum cleaner’s Location function:
Allows to locate the robot vacuum cleaner on the map.
4. CLEANING AND MAINTENANCE
Cleaning the main brush
- The main brush spins at top speed and helps pushing the dirt into the suction mouth.
This brush is in contact with the oor, and therefore with dirt, so it can wear out overtime,
aecting negatively to the cleaning eciency. For this reason, it is suggested to replace the
main brush after a maximum of 320 hours or less.
1. Slightly press the main brush frame’s tabs to open the main brush compartment and
remove it. Fig. 9
2. Remove hair, lint, and other dirt trapped in the brush and around the shafts with the help
of the self-cleaning brush. Fig. 10
3. Clear and clean the robot vacuum cleaner’s suction channel.
4. Reinstall the main brush and its frame.
Recommendation
It is recommended to clean the main brush once a week with the help of the self-
cleaning brush.