Celestron 93664 - User Manual

Pro HD WeDge
MODEL #93664
ENGLISH
1. Loosen the two latitude locking screws on both sides of the
wedge (Figure 2).
2. Push the tilt plate all the way forward as far as it will go, and
hand tighten the locking screws to hold the tilt plate in place.
3. Thread back the latitude adjustment knob so that the threaded
rod does not interfere with the orange support rod.
4. Remove the three top screws from each of the L-brackets on
the bottom of the tilt plate. Do not remove the bottom screws.
5. Place one end of the swivel block into one of the top holes
on the inside of the L-bracket. It may be necessary to loosen
the bottom screws and rotate the L-bracket enough to fit the
swivel block between the brackets.
Note: The top hole position can be used for most latitudes.
At higher latitudes the upper hole will give more stability.
However at lower latitudes the middle or lower hole
position will give more range of motion if needed.
6. Once one side of the swivel block is in place, reattach the
screws to hold the L-bracket to the tilt plate.
7. Attach the remaining L-bracket to the bottom of the tilt plate
making sure the other end of the swivel block fits inside the
corresponding hole on the bracket. Tighten both brackets.
ADjusting tHe WeDge for Your LAtituDe
Your wedge can be configured in two different ways; for latitude
range of 0° – 50°, or a latitude range of 40° - 90°. If you are at
a latitude between 40° - 50° either configuration should work
for you. The wedge comes pre-assembled in the 40° - 90°
configuration. However, if you are located at a latitude of 40° or
below you will need to adjust the latitude plates on the side of
the wedge. To adjust the latitude plates:
1. Loosen the pivot bolt on one of the side latitude plates.
2. Remove the three countersunk bolts holding the latitude plate
to the wedge.
3. Rotate the latitude plate downward so that the three holes line
up with the lower set of holes.
4. Replace the three bolts to attach the plates to the wedge
and tighten the pivot bolt.
5. Repeat the steps above for the second latitude plate.
6. Reattach the latitude locking screws and hand tighten.
Assembling the Wedge
Your Celestron telescope has a motor drive built into the base
allowing it to track the stars as they move across the sky from
east to west. However, for this drive to be useful, (particularly
for astrophotography) the telescope’s axis of rotation should be
made parallel to the Earth’s axis. The Pro HD Wedge allows you
to tilt the telescope’s axis of rotation (polar or R.A. axis) so that
the telescope can track the stars as they move in an arc around
the celestial pole. When this is accomplished, the sky’s motion
can be cancelled out simply by having the telescope rotate at
the same rate as the rotation of the Earth, but in the opposite
direction. This process is known as polar alignment.
Your wedge comes pre-assembled out of the box. However you
will need to attach the latitude adjustment rod and may need to
adjust the side latitude plate depending on your latitude.
Figure 1
Tilt Plate
L-Bracket
Swivel
Block
Figure 2
1
Pivot Bolt
Latitude
Locking
Screw
Latitude
Scale
Latitude Adjustment Knob
Latitude
Plate

Summary

Assembling the Wedge

Wedge Assembly Steps

Detailed instructions for connecting the swivel block to the L-brackets and tilt plate of the wedge.

Adjusting the Wedge for Your Latitude

Latitude Plate Adjustment

Procedure to adjust the latitude plates on the wedge for different latitude ranges (0-50° or 40-90°).

Latitude Scale Usage

Selecting the Correct Latitude Scale

Guidance on which latitude scale (east or west) to use based on the wedge's configuration.

Adjusting Wedge Center of Gravity

Shifting Side Plates for Stability

Instructions to adjust the side plates forward for improved stability at higher latitudes.

Attaching the Wedge to Your Tripod

Tripod Mounting Procedure

Steps to securely mount the wedge onto the HD tripod using alignment pins and screws.

Latitude Adjustment

Setting Proper Latitude

Process to adjust the tilt plate using the latitude knob to match the location's latitude.

Attaching the Telescope to the Wedge

Telescope Mounting Steps

Instructions for attaching the telescope's base to the wedge's tilt plate using bolts.

Polar Aligning the Wedge

Altitude and Azimuth Adjustments

Using latitude and azimuth knobs for final polar alignment adjustments in altitude and azimuth.

Tips for Use

Latitude Adjustment Knob Tip

Advice on loosening bolts for easier rotation of the latitude adjustment knob.

Latitude Pivot Bar Positions

Information on the two positions for the latitude pivot bar and its use for range of motion.

Celestron 93664 Specifications

General

Brand	Celestron
Model	93664
Category	Telescope
Language	English