Why won't SMART mode activate on my Centek Washer?
If your Centek Washer SMART mode will not activate, ensure that you select SMART mode immediately after turning the machine on. If another mode was selected first, turn the machine off and then press SMART. Also, check for a load imbalance.
What to do if my Centek CT-1953 Washer will not drain or spin and shows error code «?0?»?
If your Centek Washer isn't draining water, or spinning, or if you see error code «?0?» on the display, check the following: * Ensure the pump filter isn't blocked. * Make sure the drain hose isn't kinked or twisted. * Verify that hose end plugs were removed during installation. * Check that the drain hose or sink/sewage header isn't blocked.
Why won't my Centek CT-1953 program start?
If your Centek Washer program won't start, check these items: * Ensure the door is fully closed. * Press the ON/OFF button. * Press the Start/Pause button. * Confirm the water supply valve is open, allowing water intake. Also, check if Delayed Start is activated.
What to do if my Centek Washer constantly fills and drains water?
If your Centek Washer is constantly filling and draining water, or water remains in the drum, or the washing program stops, check these items: * Ensure the uppermost point of the drain hose is located 65 to 100 cm above the floor. * Verify the drain hose connection to the sink/sewage header isn't causing backflow. * Make sure the drain hose end is placed above the sink bottom to prevent water from flowing back. * Ensure the drain hose end isn't inserted too deep into the sewage pipe.
Why is my Centek CT-1953 Washer vibrating so much during spinning?
If your Centek Washer is vibrating strongly during spinning, check the following: * Make sure the machine is leveled. * Ensure the transport bolts have been removed. * Verify the machine isn't touching any furniture or walls. * Check for an imbalanced load.
What to do if my Centek CT-1953 won't fill with water and shows error code «?02»?
If your Centek Washer won't fill with water or displays error code «?02», check the following: * Ensure the water supply hose isn't jammed, kinked, or twisted. * Make sure the water supply tube is connected to the water supply line. * Verify the water pressure isn't too low and the water supply valve is open. * Confirm there's water in the supply system. * Check if the intake valve filter is blocked. * Ensure the Start/Pause button is pressed.
Why is my Centek CT-1953 not drying clothes properly?
If you are experiencing a low drying effect with your Centek Washer, avoid loading hard-to-dry clothes (like dense cotton) with easy-to-dry items (like synthetic fabric) simultaneously. Do not overload the machine for drying and avoid loading wet and dry clothes together for the Drying program. Also, ensure the water supply valve is closed during drying, and verify that the drain pump filter is not blocked and the drain hose isn't kinked, twisted, or blocked.
How to get rid of a bad smell from my Centek Washer?
If your Centek Washer has a smell, run the «Drum Cleaning» program.
Why won't the door on my Centek CT-1953 Washer open?
If your Centek Washer door won't open, it will remain locked until the lock icon on the control panel goes out after the program is completed.
Why is my Centek CT-1953 Washer leaking from somewhere else?
If your Centek Washer has other leaks, check the water supply tube fittings to ensure they are not loose. Check both the machine body and tap fittings. If the fittings are tight but still leak, replace the gaskets in the tube connections. Also, make sure the drain hose is correctly fastened.
Do not operate in rooms with temperatures below 5 °C.
Never use flammable sprays near the appliance.
Remove all packaging material and transport bolts before use.
Calibrate the product before using the washing machine.
Ensure the supply cable is not trapped by the machine to prevent damage.
Connect to a grounded outlet protected by a fuse.
Water and electrical connections must be done by a qualified technician.
Keep children and pets away from the hot glass door during operation.
Ensure inlet and outlet hoses are safely installed and undamaged.
Install on a dry, level surface away from sunlight and heat sources.
Remove cardboard, foam packaging, and transport triangle.
Remove four transport bolts from the back before operating.
Use threaded feet to level the machine, ensuring no deviation.
Check for rocking or wobbling by pressing the top cover diagonally.
Tighten lock nuts on all four feet after adjustment.
Water supply connection must be performed by a skilled technician.
Connect the machine exclusively to the cold water supply piping.
Screw tube nut onto valve firmly, then tighten by a quarter turn.
Screw tube nut onto the washing machine inlet and tighten.
Close the water supply valve after each use to prevent leaks.
Fix one end of the hose to the appliance; do not pull it out forcefully.
Raise hose end at least 60 cm to prevent siphon effect.
Connect to a grounded 16A socket protected by an automatic circuit breaker.
Recommended to use a dedicated lead/socket for safety.
Never use extension cables or cluster type power sockets.
Damaged power cables must be repaired by a qualified technician.
Ensure the washing machine is installed properly before use.
Run 'Hypoallergenic Wash' at 85°C without clothes to remove smells.
Check pockets, zip zippers, hook hooks, tie laces.
Sort laundry by fabric type, temperature, and contamination.
Follow symbols on care labels for fabric composition and washing.
Never wash clothes contaminated with gasoline, kerosene, or solvents.
Program for removing impurities from the drum to prevent smells.
Table detailing max load, detergent use, drying speed, temperature, and duration.
Water supply valve must be open during the drying cycle.
Activates to prevent accidental operation by children.
Machine automatically evaluates and selects washing parameters.
System detects and corrects load imbalance before spinning.
Disconnect power and water before cleaning; avoid solvents.
Regularly clean the drain pump filter for proper operation.
Check power plug, socket, and fuse.
Check door closure, ON/OFF, and Start/Pause buttons.
Check water supply valve, hose, pressure, and intake filter.
Check drain hose position and sewage pipe connection.
Check pump filter, drain hose, and hose end plugs.
Check drying speed setting or load imbalance.
Check leveling, transport bolts, and load balance.
Door unlocks after program completion; wait for lock indicator.
Check supply valve, water presence, and filter blockage.
Check drain pump filter, hose, and connections.
Close door and press Start/Pause; contact service if persists.
Turn off, disconnect power, and contact service center.
Details the 36-month guarantee and required documentation.
General| Spin speed | 1000 rpm |
|---|---|
| Control type | Electronic |
| Color | White |
| Special programs | Delicate |
| Water consumption per cycle | 45 L |
To Next Page