How to fix Centek CT-1951 Washer that will not turn on?
If your Centek Washer won't turn on, first ensure the power plug is fully inserted into the socket. Also, check the electric contact. If the issue persists, check for a power failure or replace the blown fuse.
What to do if Centek CT-1951 won't fill water or shows error code «?02»?
If your Centek Washer isn't filling with water and shows error code «?02», start by checking the water supply hose for any jams, kinks, or twists and straighten it. Ensure the water supply tube is properly connected to the water supply line and that the water supply valve is open. Verify there is water in the supply system. If the problem persists, consider increasing the water pressure or cleaning the intake valve filter. Finally, ensure that you have pressed the Start/Pause button.
Why Centek Washer program execution will not start?
If the Centek Washer program won't start, make sure the door is fully closed and that you've pressed the ON/OFF button. Also, verify that you've pressed the Start/Pause button and that the water supply valve is open, allowing water to enter the machine. Finally, check if the Delayed Start function is activated and deactivate it if needed.
What to do if Centek Washer will not drain water or spin or shows error code «?0?»?
If your Centek Washer won't drain water or spin, and displays error code «?0?», first check and clean the pump filter. Then, make sure the drain hose is not kinked or twisted, and that any hose end plugs have been removed during installation. Finally, check if the drain hose or sink/sewage header is blocked and unblock it.
Why Centek CT-1951 Washer constantly fills and drains water or water stays in the drum?
If your Centek Washer is constantly filling and draining water, or water stays in the drum, or the washing program stops, ensure the uppermost point of the drain hose is positioned 65 to 100 cm above the floor. Check the drain hose connection to the sink/sewage header to correct any backflow issues. Make sure the drain hose end is placed above the sink bottom to prevent water from flowing back, and adjust the drain hose end to be less deep in the sewage pipe.
How to reduce strong vibration during spinning of Centek CT-1951?
If your Centek Washer is vibrating strongly during spinning, make sure the machine is leveled properly. Remove the transport bolts if you haven't already. Ensure the machine isn't touching any furniture or walls. If the load is imbalanced, redistribute it evenly.
Why is my Centek CT-1951 Washer leaking from the detergent tray?
If your Centek Washer is leaking from the detergent tray, clean the detergent tray compartments. If the water pressure is too high, reduce it. Ensure the machine is level by adjusting it if it's slanted forward.
How to fix other leaks in Centek Washer?
For other leaks from your Centek Washer, check the tightness of the machine body and tap fittings on the water supply tube. If the fittings are tight but still leak, replace the gaskets in the tube connections. Also, refasten the drain hose correctly.
How to eliminate smell from Centek Washer?
To address the smell in your Centek Washer, run the «Drum Cleaning» program.
What to do if door will not open on Centek Washer?
Wait until the lock icon on the control panel goes out after program completion.
Warning about potential electric shock if the appliance or cord is damaged.
Instructions for connecting the water supply.
Guidelines for preparing and sorting clothes for washing.
Understanding care labels and checking clothes before loading.
Safety advice and how to clean the machine's exterior.
Cleaning the drum, door seal, pump filter, intake filter, and detergent tray.
General| Maximum load capacity | 6 kg |
|---|---|
| Spin speed | 1000 rpm |
| Control type | Electronic |
| Material of tank | Plastic |
| Dimensions (WxDxH) | 60x45x85 cm |
| Color | White |
| Loading type | Front |
| Special programs | Delicate |
| Protection | Child lock |
To Next Page