Cervélo P5 User Manual (English)

To Next Page

ROUTING DI2 FRAME WIRES

Down Tube E-wire

• RemovetheBatteryCoverandHiddenBatterycompartmentfromtheframeandputaside(Figure1).

• Usingelectricaltape,attachtheendoftheDownTubeE-wirethatconnectstotheDi2JunctionBoxtoamechanicalshiftercable.Feedtheshift

 cablethroughtheholeonthebackverticalwallofthe“cablebucket”untilitexitstheBBshell(Figure2,Figure3,Figure4).

TIP:ThecableandE-WireshouldremainabovetheICS3tubeswithintheframe.

TIP:Useascrewdrivertopushtheziptiesthroughthehole,onebyone.Lightlypullontheshiftcableafterinsertingeachziptie(Figure5).

• RemovetheelectricaltapeandmechanicalshiftcablefromtheE-wire.

• Slideontheheatshrinktubingtothewire.ConnectthewiretothecolormatchedcableontheDi2JunctionBox,makingsuretolineupthe

 cableproperly(Figure6).

Front Derailleur E-wire

• InserttheFrontDerailleurE-wireintothecableholeontheseattube(Figure7,Figure8).

• SlideontheheatshrinktubingandconnecttheE-wiretothecolormatchedcableontheDi2JunctionBox,makingsuretolineupthecableproperly.

Rear Derailleur E-wire

• Usingelectricaltape,attachtheendoftheE-wirethatconnectstotheJunctionBoxtoamechanicalshiftercable.Feedthecablethroughthe

 cableexitholeonthedrivesidechainstay,andouttheBBshell(Figure9).

• SlideontheheatshrinktubingandconnecttheE-wiretothecolormatchedportontheDi2JunctionBox(Figure10).

• InstalltherubberDi2grommetsuppliedwiththeframe,ontothecableexitholeonthedrivesidechainstay(Figure11).

Battery Mount

• FeedthecablefromtheDi2BatteryMountthroughthebatterypocketintherearwheelcutoutandoutthedrivesideoftheBBshell(Figure12).

• SlideontheheatshrinktubingandconnectthewiretothecolormatchedcableontheJunctionBox,makingsuretolineupthecableproperly

 (Figure13,Figure14).

• MountthefrontderailleurontheframeandconnecttheE-wire(Figure15).

• MounttherearderailleurontheframeandconnecttheE-wire(Figure16).

• Connectthebattery,frontwiringharness,andTTshifters.TesttheDi2systemforproperfunction(Figure17,Figure18,Figure19).

• Ifthesystemdoesnotwork,doublecheckallconnectionsandensurethereissufficientchargeinthebattery.Ifproblemspersist,pleasecontact

 Shimanoforfurtherassistance(Figure20).

• Ifthesystemworksproperly,disconnectthefrontharness,shiftersandbattery.Setasideforthetimebeing.

3T ADURO AEROBAR INSTALLATION

• Dry fit the fork, headset, basebar, and any spacers needed to determine the cut length of the fork steer tube based on the customer’s fit

 requirements.Westronglyrecommendadetailedmeasurementofthecustomer’scurrentbiketoensureproperforkcutlengthandt(Figure21).

NOTE:ThebearingcapisNOTneededwhenusingthe3TAdurobar.Itisrequiredwithatraditionalstemandaerobarcombination.

• Cuttheforkandinstalltheinsertintothesteertube(Figure22).

• Ifspacersarebeingused,installoneoftheantirotationspacerboltsintothefrontholeontheundersideofthe3TAdurobar(Figure23).

 NOTE:If10mmofspacersormorearerequired,thefirstspacerbelowtheAdurobarneedstobea10mmspacer.Acombinationoftwo5mm

 spacersshouldnotbeusedtogether.If10mmisneeded,two5mmspacerswillnotfittogetherproperly,pleaseusea10mmspacer.

• Afterplacingthefirstspaceronthebar,installanotherantirotationbolt.Thisprocessiscontinueduntilthelastspacerisinstalled.Thelast

 spacerdoesnotneedanantirotationbolt(Figure24).

• Attachthefairingmounttoeitherthebottomspacerordirectlytotheaerobarifnospacersarerequired.

• Mountthespacer(s),ifnecessary,andbarontotheforksteerer.Installthetopcapandbolttoensurethesystempullstogetherproperly.Torque

 theAdurosteerertubepinchboltsto5Nm(Figure25).

MAGURA BRAKE INSTALLATION

Magura Front Brake Lever Installation using the 3T Aduro Aerobar

• Removethefrontbrakecoverfromthebrake.Thisisdonewithnotools,asthecoversnapsontothebrakearm(Figure26).

 TIP:Itiseasiesttoremovethebrakecoverbygraspingthecoverfromthebackedge,andgentlypullingawayfromthecaliper.

• Removethehydraulichosefromthecaliper(NOTTHELEVER)usingan8mmopenendedwrenchandplacethecaliperaside.Donotsqueeze

 thecaliperbrakearmsnorthebrakeleverasmineraloilwillescape(Figure27,Figure28).

• UsingtheMagurahosecutter(orasharpknifeonahardsurface)cutthehosejustabovetheolive.Removethethreadednutandsetasidewiththecaliper

 (Figure29,Figure30,Figure31).

• Putaslightbendintheendofthehydraulichoseandfeeditthroughthebar(Figure32,Figure33,Figure34).

Manual

Need help?

Do you have a question about the Cervélo P5 and is the answer not in the manual?

Cervélo P5 Specifications

General

Brakes	Magura RT8 TT hydraulic
Handlebar	Cervélo P5X Aerobar
Bottom Bracket	BBright
Frame Material	Carbon
Frame	Cervélo P5
Fork	Cervélo P5
Headset	FSA IS2 1-1/8 x 1-1/8"