Chamberlain JDC7S1BMC - Table of Contents

2
Table of Contents
Safety Information 3
Safety Symbol and Signal Word Review..................3
Planning 4
Introduction 5
Voltage Selection .......................................5
Amperage ..............................................5
Operator Specications 6
Operator Dimensions 7
Jackshaft (JDC) and Hoist (JHDC) .......................7
TDC Trolley .............................................8
Battery Backup .........................................8
TDC Trolley Operators 9
Carton Inventory ........................................9
Description .............................................9
Hardware ...............................................9
TDC Trolley Assembly 10
Assemble the Operator ............................... 10
Install the Chain ....................................... 11
TDC Trolley Installation 12
Install the Header Bracket .............................12
Attach the Track to the Header Bracket and Hang the
Operator.............................................. 13
Attach the Door Arm and Bracket ..................... 14
Jackshaft (JDC) and Hoist (JHDC) Operators 15
Carton Inventory ...................................... 15
Description ...........................................15
Door Sprockets .......................................15
JDC/JHDC Assembly 16
Congure the Operator ............................... 16
JDC/JHDC Installation 17
Determine Mounting Location.........................17
Mount the Operator ................................... 18
Secure the Chain Hoist................................ 18
Cable Tension Monitors 19
Install the Cable Tension Monitor(s) (Optional) ......... 19
Manual Release 20
Emergency Disconnect System Model TDC ........... 20
Emergency Disconnect System Model JHDC.......... 20
Wiring 21
Power and Ground .................................... 21
Voltage Selection .....................................21
Wall Controller Installation 22
Factory Wiring Diagram 23
Accessory Wiring Diagram 25
Power Wiring Diagram 26
Entrapment Protection 27
Monitored Entrapment Protection .....................27
Install the Monitored Light Curtain.....................28
Battery Backup Wiring 29
Testing 30
Test all Entrapment Protection Devices................ 30
Test Wall Controller Menu Access .....................30
Test Limit Adjustment ................................. 30
Programming 31
Quick Start Commissioning ........................... 31
Manual Commissioning Program Flow .................31
Operating Modes .....................................34
Determine Operating Mode ...........................35
Determine and Set Operating Mode . . . . . . . . . . . . . . . . . . . 36
Programmable Inputs ................................. 44
Radio ................................................. 44
Programming Remote Controls and myQ® Devices .... 44
Erasing Programmed Devices . . . . . . . . . . . . . . . . . . . . . . . . . 44
Reset Defaults ........................................ 44
myQ® Smart Facility Access........................... 45
Setup a myQ® Smart Facility Access Account ......... 45
Provisioning Wi-Fi..................................... 45
Auxiliary Relays Accessory Kit ([XXXXX]) 46
Congure the Relay Adapter .......................... 46
Loop Detector Board 47
Troubleshooting 48
Maintenance 51
Maintenance Schedule................................51
Accessories 52
Field Installable Accessory Kits 55
Service Parts 56
Model TDC............................................ 56
Model JHDC .......................................... 57
Model TDC, JDC, and JHDC Common Parts ........... 57
Warranty 58
MYQ® CONNECTIVITY
• myQ® Smart Facility Access
Technology enables secure
monitoring and control of door
operators and other myQ®
Smart Facility Access devices
with a smartphone, tablet or
computer.
• Alerts can be received as email
notications, ensuring the
status of a commercial door.
SAFETY AND SECURITY
Security+ 2.0® – with every press of
the button, a new code is sent to the
commercial door operator, ensuring
a door will only open for the remote
control programmed.
UL 325 requires all commercial door
operators to be either constant
pressure to close or be equipped
with a primary external monitored
entrapment protection device.
LiftMaster® is the leading brand of
professionally installed commercial
door operators and access control
products for businesses worldwide.
We are committed to quality
products, innovative designs and
comprehensive services which
exceed our Customers’ expectations.