Chamberlain MyQ 889LM - User Manual

1
MyQ
®
CONTROL PANEL
MODEL 889LM
To prevent possible SERIOUS INJURY or DEATH from electrocution:
• Be sure power is NOT connected BEFORE installing door control.
• Connect ONLY to 7-28 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
• Install door control within sight of garage door, out of reach of children at a
minimum height of 5 feet (1.5 m) above floors, landings, steps or any other
adjacent walking surface, and away from ALL moving parts of door.
• NEVER permit children to operate or play with door control push buttons or
remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly adjusted, and
there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed. NEVER permit
anyone to cross path of closing garage door.
• DO NOT install this door control on garage door opener systems controlling
one-piece or swing doors.
To provide an adequate visual alert, the garage door opener light bulb(s) MUST
be a minimum of 40 Watt (or equivalent).
The MyQ Control Panel is intended to be installed with Security+
®
Garage Door
Openers manufactured between 1998 and present. The MyQ Control Panel is NOT
compatible with Security+ 2.0
®
Garage Door Openers. DO NOT install this door
control on garage door opener systems controlling one-piece or swing doors.
APPLICATION
The MyQ Control Panel offers a quick and convenient way to add Security+ 2.0 and
MyQ technology to your existing garage door opener. MyQ technology uses a
900MHz signal to provide two-way communication between the garage door
opener and MyQ enabled accessories. When programmed to the LiftMaster
®
Internet Gateway you can monitor and control your garage door from any internet
enabled computer or smartphone. You may program up to 12 Security+ 2.0
remote controls, 2 Security+ 2.0 keyless entries and a combination of 16 MyQ
accessories to the MyQ control panel.
COMPATIBLE ACCESSORIES
Security+ 2.0
®
Accessories: MyQ Accessories:
Model 891LM
1- Button Remote Control
Model 823LM
Remote Light Switch
Model 893LM
3-Button Remote Control
Model 825LM
Remote Light Control
Model 890MAX
3-Button Mini MAX Remote Control
Model 828LM
LiftMaster
®
Internet Gateway
Model 893MAX
3-Button MAX Remote Control
Model 829LM
Garage Door and Gate Monitor
Model 895MAX
3-Button Premium MAX Remote Control
Model 877LM
Wireless Keyless Entry
Model 877MAX
Wireless MAX Keyless Entry
OVERVIEW
Install the MyQ Control Panel in place of the existing door control, within sight of
garage door, out of reach of small children at a minimum height of 5 feet (1.5 m)
above floors, landings, steps or any other adjacent walking surface, and away from
ALL moving parts of door. Due to power consumption the MyQ Control Panel
cannot be used in conjunction with another wired door control connected to your
garage door opener. If an additional door control is needed, the wireless door
control model 885LM can be programmed to the MyQ Control Panel.
To program the 885LM to the MyQ Control Panel, follow the remote control
programming steps. When in battery back-up mode, any feature using unattended
operation such as Timer-to-Close, closure from a garage door and gate monitor or
remote operation utilizing the LiftMaster
®
Internet Gateway will be disabled.
1. Disconnect all electrical and battery power (if applicable) to the garage door
opener.
2. Remove the existing door control from the wall.
3. Note the polarity of the wires connected to the existing door control.
• Label the wire connected to the RED terminal.
• Label the wire connected to the WHITE terminal.
Disconnect the wires from the existing door control.
4. Connect the wires to the new MyQ Control Panel. Make sure the polarity is
correct.
• Red wire to the R terminal.
• White wire to the W terminal.
INSTALLATION
Existing Door Control
Discard, donate
or recycle
Wire from
RED terminal
Connect
RED wire to
R terminal
Wire from
WHITE
terminal
Connect
WHITE
wire to W
terminal
MyQ Control Panel
5. Mount the MyQ Control Panel to the wall.
6. Reconnect power. The yellow command LED and the red learn LED will
blink quickly for up to 5 minutes as the control panel recharges. When the
control panel is operational, the yellow command LED will glow steadily.
7. To test the control panel, press the push bar to activate the garage door
opener.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.

Summary

Application

Overview of MyQ Control Panel

Compatible Accessories

Safety Warnings

Electrical Shock Hazard

Warning about connecting power before installation.

Garage Door Injury Hazard

Warnings about door closing, child operation, and obstructions.

One-Piece or Swing Door Warning

Do not install on systems controlling one-piece or swing doors.

Light Bulb Requirement

Requirement for a minimum 40-watt bulb for visual alert.

Chemical Exposure Warning

Warning about California Proposition 65 chemical exposure.

Installation Guide

Installation Location

Placement advice for the control panel, away from children.

Wiring Instructions

Steps for disconnecting power, removing old control, and connecting wires.

Mounting and Power-Up

Mounting the panel and reconnecting power for initial charge.

Testing Operation

How to test the installed control panel's functionality.

Programming Instructions

Remote Control Programming

Steps to program a remote control to the MyQ panel.

Keyless Entry Programming

Steps to program a keyless entry keypad.

MyQ Enabled Accessories Programming

How to program MyQ accessories like light switches.

LiftMaster Internet Gateway Setup

Control Panel Functions

Push Bar Operation

How to use the push bar to open or close the door.

Light Control

How to turn garage door opener lights on/off and adjust duration.

Motion Sensor Function

How the motion sensor activates the opener lights.

Timer-to-Close (TTC)

How to set the door to close automatically after a set time.

Lock Feature

How to activate/deactivate the lock feature, disabling remotes.

Erasing Devices from Memory

Erase Remote Controls and Keyless Entries

Steps to erase remotes and keyless entries from the panel.

Erase All Devices

Steps to erase all programmed accessories, including MyQ.

Troubleshooting Common Issues

Warranty Information

Chamberlain MyQ 889LM Specifications

General

Connectivity	Wi-Fi
Compatibility	Compatible with most garage door openers
Mobile App	MyQ App
Voice Control	Amazon Alexa, Google Assistant
Notifications	Real-time alerts
Display	LED indicators
Features	Remote control of garage door, real-time status