Chamberlain Power Drive 3132E FS2 User Manual

Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
■ Periodic checks of the opener are required to ensure safe operation.
■ The model number label is located on the front panel of your opener.
®
GARAGE DOOR OPENER
Models 3132E FS2 • 3142E FS2
For Residential Use Only

Chamberlain Power Drive 3132E FS2 Specifications

General

Brand	Chamberlain
Model	Power Drive 3132E FS2
Category	Garage Door Opener
Language	English

Summary

Preparing Your Garage Door

ASSEMBLY STEP 1: Assemble Rail & Attach Pulley Bracket (Sectional/One-Piece Doors)

For Sectional and One-Piece Doors ONLY

Instructions for assembling the rail and attaching the pulley bracket for specific door types.

ASSEMBLY STEP 1: Assemble Rail & Attach Pulley Bracket (Sliding/Swinging Gates)

For Sliding and Swinging Gates ONLY

Instructions for assembling the rail and attaching the pulley bracket for gates.

ASSEMBLY STEP 2: Install the Trolley

ASSEMBLY STEP 3: Fasten the Rail to the Motor Unit

ASSEMBLY STEP 4: Install Chain/Cable & Attach Sprocket Cover (Sectional/One-Piece Doors)

For Sectional and One-Piece Doors

ASSEMBLY STEP 4: Install Chain/Cable & Attach Sprocket Cover (Sliding/Swinging Gates)

For Sliding and Swinging Gates

ASSEMBLY STEP 5: Tighten the Chain and Cable

IMPORTANT INSTALLATION INSTRUCTIONS

Reduce Risk of Severe Injury or Death

Critical safety warnings and instructions to follow before installation.

INSTALLATION STEP 1: Determine Header Bracket Location (Sectional/One-Piece Track)

Sectional Door and One-Piece Door With Track

INSTALLATION STEP 1: Determine Header Bracket Location (One-Piece Door Without Track)

INSTALLATION STEP 2: Install the Header Bracket

Wall Header Bracket Installation

Ceiling Header Bracket Installation

INSTALLATION STEP 3: Attach the Rail to the Header Bracket

INSTALLATION STEP 4: Position the Opener

Sectional Door or One-Piece Door With Track

One-Piece Door Without Track

INSTALLATION STEP 5: Hang the Opener

INSTALLATION STEP 6: Install the Door Control

Wiring Instructions for Accessories

INSTALLATION STEP 7: Install the Light

INSTALLATION STEP 8: Attach Emergency Release Rope and Handle

INSTALLATION STEP 9: Electrical Requirements

INSTALLATION STEP 10: Fasten the Door Bracket (Sectional Doors)

Sectional Doors

INSTALLATION STEP 10: Fasten the Door Bracket (One-Piece Doors)

One-Piece Doors

INSTALLATION STEP 11: Connect Door Arm to Trolley (Sectional Doors ONLY)

Sectional Doors ONLY

INSTALLATION STEP 11: Connect Door Arm to Trolley (All One-Piece Doors)

All One-Piece Doors

ADJUSTMENT STEP 1: Adjust UP and DOWN Travel Limits

How and When to Adjust the Limits

Guidelines for adjusting the door's open and close travel limits.

ADJUSTMENT STEP 2: Adjust the Force

How and When to Adjust the Forces

Procedures for adjusting the force required to open and close the garage door.

ADJUSTMENT STEP 3: Test the Safety Reversal System

Garage Door Installation

How to test the safety reversal system for garage doors.

Gate Installation

How to test the safety reversal system for gates.

OPERATION

Important Safety Instructions

Critical safety warnings for operating the garage door opener.

Using the Wall-Mounted Door Control

To Open the Door Manually

Having a Problem?

Opener Doesn't Operate

Door Stops or Reverses

PROGRAMMING

To Add or Reprogram a Hand-held Remote Control

Step-by-step guide to program remote controls to the opener.

To Add, Reprogram or Change a Keyless Entry PIN