Chicago Electric 68221 User Manual

Chicago Electric 68221

14 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Electric Chainsaw Sharpener

68221 Electric Chainsaw Sharpener

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

When unpacking, make sure that the product is intact and undamaged. If any parts

are missing or broken, please call 1-800-444-3353 as soon as possible.

Visit our website at: http://www.harborfreight.com

Copyright

©

2010 by Harbor Freight Tools

®

. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Table of Contents

Other manuals for Chicago Electric 68221

Owner's Manual & Safety Instructions16 pages

Questions and Answers:

C
Christine MartinezAug 12, 2025
What to do if my Chicago Electric 68221 will not start?
- G
  Gregory PowellAug 12, 2025
  If your Chicago Electric Power Tool won't start, there are several potential causes. First, ensure the power cord is properly connected. Second, verify that the outlet has power; if not, check the circuit breaker, making sure the circuit's capacity is adequate for the tool and isn't overloaded. Third, if your tool has a thermal reset breaker, turn it off, let it cool, and then press the reset button. Finally, internal damage or wear may be the issue, in which case you should have a technician service the tool.
T
Tiffany DixonAug 16, 2025
Why is my Chicago Electric 68221 overheating?
- T
  tmullenAug 16, 2025
  Overheating of your Chicago Electric Power Tool can occur for several reasons. Avoid forcing the machine to work too fast; allow it to operate at its own pace. Ensure cutting accessories are sharp, replacing them if needed. Clear any blockages from the motor housing vents, using compressed air while wearing ANSI-approved safety goggles and a NIOSH-approved dust mask/respirator. Lastly, eliminate the use of extension cords if possible, or use an extension cord with the proper diameter for its length and load.
S
scott90Aug 20, 2025
Why does my Chicago Electric 68221 performance decrease over time?
- B
  Brian HuffmanAug 20, 2025
  Decreased performance in your Chicago Electric Power Tool over time can be due to a couple of factors. Check if the accessory is dull or damaged, and keep cutting accessories sharp, replacing them as needed. Also, worn or damaged carbon brushes may be the cause, and you should have a qualified technician replace them.
M
moyerchristopherAug 23, 2025
How to fix a slow operating Chicago Electric 68221 Power Tool?
- L
  Laura SanchezAug 25, 2025
  If your Chicago Electric Power Tool is operating slowly, the extension cord may be too long or the wire size too small. Try eliminating the extension cord. If you need an extension cord, use one with the correct diameter for its length and load.
D
David FoleyAug 27, 2025
What causes excessive noise in my Chicago Electric Power Tool?
- A
  Adriana RodriguezAug 27, 2025
  Excessive noise or rattling in your Chicago Electric Power Tool can be caused by internal damage or wear, such as with the carbon brushes or bearings. In this case, have a technician service the tool.
V
Vickie BrownAug 31, 2025
Why does the performance of my Chicago Electric 68221 Power Tool decrease over time?
- A
  Amanda DavisAug 31, 2025
  If the performance of your Chicago Electric Power Tool decreases over time: * The accessory may be dull or damaged. Keep cutting accessories sharp and replace them as needed. * The carbon brushes may be worn or damaged. Have a qualified technician replace the brushes.
M
Martin WagnerSep 3, 2025
Why is my Chicago Electric 68221 making excessive noise?
- B
  Barbara DaySep 4, 2025
  If your Chicago Electric Power Tool is making excessive noise or rattling sounds, it may be due to internal damage or wear, such as worn carbon brushes or bearings. Have a technician service the tool.
M
michele34Sep 7, 2025
How to fix a Chicago Electric 68221 that operates slowly?
- K
  kthompsonSep 7, 2025
  If your Chicago Electric Power Tool operates slowly, it might be because the extension cord is too long or the wire size is too small. Try eliminating the extension cord. If you need one, use a shorter or heavier gauge cord.

Chicago Electric 68221 Specifications

General

Type	Angle Grinder
Disc Diameter	4-1/2 in.
Voltage	120 V
No Load Speed (RPM)	11, 000 RPM
Spindle Lock	Yes
Power Source	Corded Electric
Wheel Diameter	4-1/2 in.
Arbor Size	5/8 in.
No Load Speed	11000 RPM
Spindle Thread	5/8"-11 UNC

Related product manuals

Chicago Electric 68987

Preview: Chicago Electric 68012

Chicago Electric 68012

Preview: Chicago Electric 68861

Chicago Electric 68861

Preview: Chicago Electric 68523

Chicago Electric 68523

Preview: Chicago Electric 67537

Chicago Electric 67537

Preview: Chicago Electric 62422

Chicago Electric 62422

Preview: Chicago Electric 61687

Chicago Electric 61687

Preview: Chicago Electric 62866

Chicago Electric 62866

Preview: Chicago Electric 67119

Chicago Electric 67119

Preview: Chicago Electric 67631

Chicago Electric 67631

Chicago Electric 66182

Preview: Chicago Electric 67632

Chicago Electric 67632