Chicco NEPTUNE - Fitting for Group 2-3 Child (15-36 kg); Adjusting Headrest Height; Refitting Harness for Group 1 Child; Cleaning and Maintenance

9
8
thebuttononthebuckleandmovethemtothesides
(diag.14)
8. Makesure your child isseated comfortablyon the
childcar seat, adjustthe harness strapsaroundthe
childsbodywithoutpullingthemtootight,jointhe
twoharnessstraps(diag.15A)andclickthemintothe
buckle(diag.15B).
9. Use the adjuster knob A tted at the top of the
backrestto adjustthe height ofthe child car seat’s
headrest,itmustbettedsoastoallowtheharness
strapstocomeoutattheheightofthechild’sshoul-
ders(diag.16)
10.Totightentherestraintharnessesofthechildcarseat,
pulltheadjustmentstrapIuntilitiscorrectlyttedto
thechild’sbody.
11. Checkthatthechildcarseatisttedcorrectlyasseen
inthediagram(diag.18).
To removethe child from the child carseat, press the
buttonon the buckle and releasethe restraintharness
(diag.19)
FITTING THE CHILD CAR SEAT INTO THE CAR AND
SEATING A GR. 2 or 3 CHILD (15-36 KG)
TochangethecongurationofthechildcarseatfromGr.1
toGr.2-3,itisnecessaryrstofalltoremovetherestraint
harnessfollowingtheinstructionsbelow:
1. Releasethechildcarseatharnessesfromthebuckle
(diag.14)
2. Rotate and release the two belt routing plates R
foundundertheseat(diag.20A)slidingthemoutof
thetwoslotsinthefabriccover(diag.20B).
3. Removethetwoharnessstrapsfromthelockingpla-
teQ(diag.21)
4. RotateandreleasethetwobeltroutingplatesNfrom
thebackrest(diag.22)
5. Fromthefrontoftheseat,slideoutthetwosections
oftheharnessthroughthetworeddiagonalbeltrou-
tingslotsC(diag.23).
6. Store these two harness straps in a safe place for
futureuse.
7. Now slide the buckle and the fabric crotch strap
throughtheslotinthecentreoftheseat,sothatit
alltsinsidethehousingonthechildseat(diag.24A,
24Band24C).
ThechildcarseatisnowreadytobeinstalledforGroup
2and3children.
8. Placethechildcarseatontothechosenforwardfa-
cingcarseat(diag.25)
9. Threadthediagonalcarsafetybeltdownbehindthe
headrestandthroughtherelativereddiagonal belt
routingslot C belowthe headrest.Placeyour child
carefullyintothecarseat, andcheckthatthechild
is sitting with his backcorrectly placed againstthe
backrestofthechildcarseat(diag.26)
10.Clickthecarsafetybeltintothebucklesothatboth
theabdominalandthediagonalstrapspassunderthe
armrest(diag.27).
11. Check the height of the head rest and, if it is not
correct,adjust itaccordingly: seeparagraph “ADJU-
STINGTHEHEIGHTOFTHEHEADREST”
12. Pullthediagonalcarsafetybeltstraptowardsthere-
tractor,toensurethebeltistightandttingproperly
overthechild’slegsandchest(diag.28).
13.Checkthatthechildcarseatisttedcorrectlyasseen
inthediagram(diag.29).
WARNING!
• Alwayscheckthattheseatbeltispositionedcorrectly
andnopartsaretwisted.
• Check that the diagonal safety belt ts correctly
acrossthechild’sshoulderanddoesnotpressonhe
childsneck;adjusttheheadrestaccordingly.
• Checkthatthecarsafetybeltretractorisbehindthe
backrestofthecarseat(oratleastalignedtoit).
ToremoveachildfromaGroup2and3childcarseat:
1. Releasethecarsafetybeltfromitsbuckle.
2. Removethecarsafetybeltfromthechild’sbody.
3. Carefullyremovethechildfromthecarseat.
WARNING!Ifyoudonotintendtoremovethechildcar
seatfromthevehicle,slotthecarsafetybeltsbackinto
thebuckle,sothatthechildcarseatremainsfastenedsa-
felyinsidethevehicleevenwhennotused;thiswillavoid
dangerduringanaccidentorsuddenbrakingofthecar.
ADJUSTING THE HEIGHT OF THE HEAD REST
Theheightoftheheadrestcanbeadjustedtoarangeof
positionstoadaptthechildcarseattotheheightofthe
child.Whenitiscorrectlyadjusted,itensures:
• Thatthechild’sheadisalwaysheldinplaceandwell
protected(Gr.1-2-3).
• Thatthechildcarseatrestraintharnessesarealways
attherightheight,thatistheshoulderstraps(Gr.1).
• Thatthediagonalcar safetybeltsarealwaysatthe
rightheightasthestrapsareslottedthroughthehe-
adrestC(Gr.2-3).
Toadjusttheheightoftheheadrest,turntheknobAt-
tedatthetopofthebackrestuntilyoureachtherequired
height(diag.16).
REFITTING THE HARNESS FOR SEATING A GR. 1
CHILD (9-18 KG)
Torettherestraintharnesstothechildcarseat,proceed
asfollows:
1. Jointhetwoendsoftheharnessstraps,insertthem
andconnectthemtothebuckle(diag.30)
2. Insert the two locking plates R,  sliding them out
throughtheslotsinthefabriccoverandpullingthem
outfromundertheseat(diag.31).
3. InsertthetwoshoulderstrapandthebeltsequenceN
lockingplatesthroughthetworeddiagonalbeltslots
Candthenthroughthebackrest(diag.32).
4. Connectthetwoharnessstrapstothelockingplate
Q(diag.33).
CLEANING AND MAINTENANCE
HOW TO CLEAN THE FABRIC COVER
Thechildcarseat’sfabriccovercanberemovedandclea-
nedbyhandorinawashingmachineat30°C.Pleasere-