4 x Alkaline batteries AA
4 x Screws
Instructions
STANDARD
PRO
www.chickenguard.com
English - French - Dutch
1 x instructions Booklet1 x ChickenGuard Unit
Clock 12/24hr.
=12hr =24hr
=YES
to continue
=YES
to continue
=YES
to continue
Instructions
STANDARD/PRO
Step 3
Install the 4X AA batteries.
Connect the wires from the
motor to the white socket
on the inside of the front
panel labelled “Motor”.
Step 4
Attach the front panel,
screwing in the captive
screws.
Step 1
Unscrew the front panel
captive screws.
CENTRE LINECENTRE LINE
Using the 4 screws provided,
attach the unit to your coop
aligned to the right so that
the string is positioned on
the centre of the coop door
and running vertically.
Step 2
Open Settings
Manual/Sensor/Timer
MANUAL
This option is to manually open or close the door by pressing
either the UP or DOWN buttons.
SENSOR
This option is for automatic opening of the coop door at
dawn, or the automatic closing in the evening, after sunset,
using the ‘Light Sensor’.
TIMER
This option is for automatic opening of the coop door in the
morning, or automatic closing in the evening, at your set
time/s. Press UP or DOWN to set the open/close Times.
5-
Close Settings
Manual/Sensor/Timer/LUX+
LUX+ ( Dual Safety Closing ) - This setting uses a combination of
both the ‘Light Sensor’ and ‘Timer’ to close the door. The door
opener will use the ‘Light Sensor’ as its’ primary method to close,
but, if it is not dark enough the door will then close based on the
default time you set.
You have 4 options Manual, Sensor, Timer and LUX+.
6-
Your ChickenGuard is ready to use!
WHAT’S IN THE BOX?
Device can be used to a maximum altitude of 5000m.
The appliance is not to be used by persons (including children)
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction.
The appliance is not a toy: Children should be supervised at all
times when coming into contact with
the device.
Only install 4 x new AA Alkaline batteries 1.
When the batteries need changing, the red LED on the front
panel will be permanently lit.
2.
The red LED on the front panel always flashes every 3 minutes
when the door is CLOSED.
3.
When changing batteries, you will need to reset the time.4.
Do not attempt to recharge Non-rechargeable batteries. 5.
Batteries are to be inserted with the correct polarity. 6.
Exhausted batteries are to be removed from the appliance and
safely disposed of.
7.
If the appliance is to be stored unused for a long period, the
batteries should be removed.
8.
The supply terminals are not to be short-circuited. 9.
ABOUT BATTERIES
The door opener comes equipped with the ability to accept
external Solar or DC power. The socket is located behind the
rubber bung on the bottom right of the unit.
The power supply needs to be 9 Volt DC with 1 Amp capability.
The socket is centre positive, 2.1mm DC power plug compatible.
EXTERNAL POWER
1
How to install your ChickenGuard?
Initial Setup Guide
- Steps 1-2-3-4-5-6
2
Press UP or DOWN to set the hour and then the MENU button to
save. Press UP or DOWN to set the minutes and then MENU to
save.
3-
Language
Press Up or Down
Press UP or DOWN to choose your language and press MENU to
save.
2-
Setup Wizard
When the screen is on, Press the MENU button and scroll to the
Setup Wizard. Press the MENU button again to get started. “By
pressing the UP or DOWN buttons you can navigate through the
menus.”
1-
Door Calibration
Set-up 2 of 4
Press UP or DOWN to manually set the fully open and closed
positions of the door.
4-
1/5
To Next Page
Need help?
General
