3. Use instructions
11
8) “High Wind” button: In the mode of dehumidification, the “High Wind” button has no effect.
9) “Sleep” button: Press the “Sleep” button to switch “Sleep”→ “Sleep Cancel” → “Sleep”. If it is in the
state of “Sleep”, the “Sleep” will not be cancelled after the mode is switched.
10) “Lock” button: Press this button and the remote controller will switch “Lock” → “Unlock” → “Lock”.
When the “Lock” button is actuated, all buttons except for the “Lock” button on the remote controller
have no effect.
11) “Lamp” button: Press this button and the remote controller will switch “Lamp Display” → “Lamp
Display Cancel” → “Lamp Display”. If the “Lamp Display” is actuated, the “Lamp Display” will not be
cancelled after the “Mode” button is pressed.
12) “Purification” button: Press this button and the remote controller will switch “Purification” →
“Purification Cancel” → “Purification”. If the “Purification” is actuated, the “Purification” will not be
cancelled after the “Mode” button is pressed.
4. “Heating” mode:
1) “Running On/ Off” button: Press this button and the remote controller will switch “On” → “Off” →
“On”. After shutdown, it will cancel such functions as “Lamp”, “Purification”, “Sleep”, “High Wind” or
“Timing”. In time of “Off” → “On”, other button settings will follow the settings before “Off”.
2) “-” button: The set temperature will have 1°C decreased once this button is pressed, and the
Celsius models will decrease progressively from “32°C → 31°C→…→17°C→16°C”;
3) “+” button: The set temperature will have 1°C increased once this button is pressed, and the
Celsius models will increase progressively from “16°C → 17°C→…→31°C→32°C”;
4) “Swing” button: Press this button to switch “Swing” → “Fixed Wind” → “Natural Wind” → “Swing”.
5) “Wind Direction” button: Press this button to switch “Swing” → “Stop” → “Swing” .
6) “Fan Speed” button: Press this button to switch “Auto Wind” → “High Wind” → “Moderate Wind” →
“Low Wind” → “Auto Wind” .
7) “TIMER” button: Press this button to set the timer by 1 hour, respectively 1H, 2H, ..., 24H, Cancel
and 1H. In the “Off” state, press the “TIMER” button to set the “On” time, the remote controller
displays the running state before “Off” (In case of initial power-on, it will enter the default state of the
auto mode), and the timer displays 1H. Press the “TIMER” button again to repeat 2H ... 24H, Cancel,
1H, ... in order. In the “On” state, press the “TIMER” button to set the “Off” time, and the timer displays
1H. Press the “Off” button again to repeat 2H ... 24H, Cancel, 1H, ... in order. After the timer function
is set, decrease every 1 hour until the “On” or “Off” time, and simultaneously disable the timer display.
If the “Mode” button is pressed in time of “Timing”, the “Timing” will not be cancelled.
8) “High Wind” button: Press this button, and the remote controller will switch “High Wind” →
“Cancel”→ “High Wind”. When the “High Wind” button is actuated, it will not display the fan speed, but
the “High Wind” will be cancelled after the mode is converted and if it is set as sleep running, then the
“High Wind” running will be cancelled.
9) “Sleep” button: Press the “Sleep” button to switch “Sleep”→ “Sleep Cancel” → “Sleep”. If it is in the
state of “Sleep”, the “Sleep” will not be cancelled after the mode is switched. Set the “High Wind”
running to cancel the “Sleep” running.
10) “Lock” button: Press this button and the remote controller will switch “Lock” → “Unlock” → “Lock”.
When the “Lock” button is actuated, all buttons except for the “Lock” button on the remote controller
have no effect.
11) “Lamp” button: Press this button and the remote controller will switch “Lamp Display” → “Lamp
Display Cancel” → “Lamp Display”. If the “Lamp Display” is actuated, the “Lamp Display” will not be
cancelled after the “Mode” button is pressed.
12) “Purification” button: Press this button and the remote controller will switch “Purification” →
“Purification Cancel” → “Purification”. If the “Purification” is actuated, the “Purification” will not be
cancelled after the “Mode” button is pressed.
To Next Page
Loading...
