Chunghop RM-88E - TV Setup Guide; Manual TV Code Entry; Automatic TV Code Search; VCD Setup Guide

Setting Steps for TV Set
Manual Setting
1.Find out the 3-digit code for the TV that you
desire
to
control
from
the
“code
list”
.In
case
Search
code
4
there
are
several
groups
of
codes
available,
y
please use the first group at first;
2.Press and hold the “Setting” button at first, Press and hold [Setting] + | TV
then press the “TV” button. Release both the “Setting”
buttons
after
the
indicator
light
illuminates,
button,
then
Я №
аниме
indicating
the
status
of
code
input;
pessi
Indicator
light
illuminates
3.Input
sequentially
the
3-digit
code
that
you
have
«Ty”
button
y
obtained.
The
indicator
light
flashes
once
when
`
Release
both
buttons
one
digit
is
input.
After
the
input
of
the
code,
the
y
indicator
light
extinguishes;
Input
the
®
四
С
Note:
In
case
the
indicator
light
keeps
illuminating 3-digit
code.
after
two
flashes,
you
only
need
to
input
the
y
No
correct
3-digit
code
and
do
not
repeat
Step
Indicator
light
extinguishes
2,
otherwise
a
resetting
started
from
Step
2
{
Yes
shall commence. 5
Setting ends
4.When
the
indicator
light
extinguishes,the
setting
ends.Please
test
the
remote
control
can
work
normally
or
not,if
not,
reset
it
from
step
1
and
try
next
3-digit
code
Search For the Correct Code
In
case
that
your
TV
cannot
be
remotely
controlled
after
all
the
codes
available
are
tried,
or
in
case
that
your
TV
is
the
brand
that
has
no
matching
code
in
the
“code
list”
,
you
may
try the following steps:
1.Manually
switch
o
the
TV
that
you
desire
to
control,it
should
be
in
playing
state
2.Aim
the
remote
controller
at
the
TV.
Press
and
hold
the
“Setting”
button
at
first,
then
press
the “TV” button. At this time, the indicator light illuminates. Then release both buttons.
3.Press the “Volume Up” button on the remote controller and release it to observe whether
the volume indication on the TV is shown. Repeat the operation till the volume indication on
the TV is shown, and then press the “Setting” button.
Note:
Each
press
of
the
“Volume
Up”
button
will
lead
to
one
code
emission.
If
the
code
is
identifiable by the TV, the volume of the TV program will change.
4.At this time, the indicator light extinguishes, and the setting ends. You can check other
functional buttons, for example, “Power” to ensure that they work well.
5.In case other buttons fail to work properly, a resetting started from Step 2 shall commence till
the correct code is found.
Note: After each press of “Volume Up” button, the code number of the remote controller will
add 1 and the “Volume Up” code under the code will be emitted once. In case a normal
control still cannot be obtained, please refer to the “Problem Solving” .
Setting Steps for VCD Machine
Manual Setting
1.Find out the 3-digit code for the VCD machine
that you desire to control from the “code list” .
In case there are several groups of codes рз Sd Hold JSearch cedo
available, please use the first group at first; the “Setting”
2.Press and hold the “Setting” button at first, button, then y
then
press
the
“VCD”
button.
Release
both
press
the
Setting|+
|
VCD
buttons
after
the
indicator
light
illuminates,
“VCD”
button.
y
indicating the status of code input; Indicator light illuminates
3.Input sequentially the 3-digit code that you
have obtained. The indicator light flashes Release both buttons
once when one digit is input. After the input E 1
of the code, the indicator light extinguishes; Input the
Note: In case the indicator light keeps 3-digit code. (9 (9 (9
illuminating after two flashes, you only need y
to input the correct 3-digit code and do not Indicator light extinguishes
repeat Step 2, otherwise a resetting started > { Yes
from Step 2 shall commence. Setting ends
4.When the indicator light extinguishes,the setting ends.Please test the remote control can work
normally ог not,if not, reset it from step 1 and try next 3-digit code