36 RP _STE(Tail tone elimination
in
communication through
OFF/1,2,3
... 10
repeater)
37 RPT _ RL{Dtlay the tall tone of repeater) OFF/1,2,3 •.• 10
38 PONMGS(Boot display) FULUMGS
39 ROGER(tone end oftnnsmlsslon) ON/OFF
40 RESET (Restore to ddault setting) VFO/ALL
12.2.-SHORTCUT MENU OPERATlON:
].-Press the key MENU,then press the key A or T to select the desired menu.
2.-Press the key MENU again, come to the parameter setting.
3.-Press the key A. or T
to
select the desired parameter.
4.-Press the key MENU to confirm and save, press the key EXIT
to
cancel setting or clear the input.
E E E
"MENU
NO.
..
MENU
NO.
.. ..
"MENU
NO.
PARAMEn:R
...
PARAMEn:R AllAMEn:R
.
PARAMITER
G) CID @ @
-Note:
Under channel mode,the following menu settings are lnvaHd:CTCSS,DCS,W/N,PTT-ID,BCL,SCAN
ADD TO,S..CODE,CHANNEL NAME.Only the H/L power could be changed.
12.3.-"SQL" (SQUELCH),
-The squelch mute the speaker of the transceiver
io
the absence of recepdon. With the squelch level correctly
set, you will hear sound only
while
actually receiving signals and
significantly
reduces
battery
current
consumption. It is recommended
that you
set Level 5.
12.4.- FUNCTION "VOX" (VOICE OPERATED TRANSMISSION):
-This function is not necessary
to
push the [PTT] on the transceiver
for
a transmission.
Transmission
is
activated automatically
by
detecting the radio voice. When finish speaking, the transmission automatically
terminated
and the
transceiver
will
automatically receive signal. Be sure to adjust
the
VOX Gain level
to
an appropriate sensitivity to allow smooth transmission.
12.5.- SELECT WIDEBAND OR NARROW BAND "WIN":
lo areas where the RF signals are saturated, you must use the narrow band of transmission to avoid
interference in adjacent channels.
12.6.-TDR (
D
UAL WATCH/DUAL RECEPTION),
This
feature
allows you
to
operate between
frequency
A and frequency
8.
Periodically, the
transceiver
checks
whether a signal is received on another frequency
that
we have scheduled. If you receive a signal, the
unit
14
will remain in the frequency until the received signal disappean.
12.
7
.- TOT(TRAN SM JSSIO N TIMER),
This function can automatically control the time we transmit each time you
press
(P1TI on the transceiver.
This feature is
very
useful to avoid overheating excessive power transiston of the
transceiver.
The transceiver
will be off transmission automatically once the set
time.
12.8.-CTCSS/DCS:
In some
cases
only
want
to
establish communications in
a
closed user group
at
a particular frequency
or
channel, ror It will use "CTCSS" or code "DCS" for reception.
The "squdc
b
" opens only when receiving
a
frequency
with "CTCSS" or codes "DCS" same as the programmed
in your
transceiver.
If
codes of the received signal differs from
those
programmed in your transceiver,
the
"squelch" will not open and the received signal can be beard.
Note:
- The use of "CTCSS" or "DCS" in a communication, does not guarantee complete confidentiality
communication.
12.9.-ANI
-ANI
(Automatic Number Identification) is also known as PTT ID because an ID is transmitted when the
PTT button of the radio
is pressed
and/or
released.
This ID tells
the
di
s
p
at
c
h
er which field
radio was keyed.
Only could be set by PC software.
12.10.- DTMFST (
D
T
MF TON
E
OF
TRANSMJTTING CODE),
Finl you should set the PTI-ID as BOT/EOT/BOTH
-"OFF"-Under transmitting mode,
you
can't
bear
the DTMF
tone, whUe you press the
key to transmJt
the
code or code automatically traosmJtted..
-"DT-ST"-Under transmitting mode, you can hear the DTMF tone, while you press the key
to
transmJt
the code.
-"
ANI..
S
T
"-und
e
r transmitting
mode,
you
can hear the
DTM
F
tone,
while
the
code
automatically
tran
s
mitted
.
-"DT-ANl"-under transmitting mode, you can bear the DTMF
tone, while you press
the key
to transmJt
the code
or
the code automatically transmitted..
12.11.- SC-REV(SCAN RESUME
METHOD),
This transceiver allows you to scan memory channels, all
the
bands or part of the bands.
When
the transceiver detects a communication, the scan
will
stop automatically.
Notea:
-
"TO"
(Time Operation):
Scanninc
will atop when
Jt
detects
an
active
signal The scannlnc will stop on each channel or
active frequency for a predetermined time, after that time
the scan
will resume
automatically.
-
"CO"
(Carrier Operation):
The scannlnc will stop and remain
in the frequency
or
channel, until the
active
sle;nal diaappean.
- "SE"(Searcb Operation):
The scanning will stop and remain In the frequency or channel after It detects
an
active signal.
15
To Next Page
Loading...