clage MBH Series - User Manual

Questions and Answers

L
Lindsay Gordon PhDAug 17, 2025
What to do if my clage Water Heater does not switch on and the water remains cold?
- C
  Cameron HuertaAug 17, 2025
  If your clage Water Heater is not switching on and the water remains cold, there might be several reasons: * The water connections could be mixed up; in this case, check the installation. * The water flow pressure might be too low; in this case, check the water flow setting (by authorised technician), open the angle valve further, and check the water pressure. * There might be dirt in the pipes; in this case, remove dirt from the inlet and outlet pipes.
A
Angel RiveraAug 19, 2025
Why is the hot water temperature too low on my clage Water Heater?
- S
  Spencer LoveAug 19, 2025
  If the hot water temperature of your clage Water Heater is too low, it could be due to a high flow rate, a low inlet temperature or a low power supply. You can adjust the water flow (by authorised technician) or check the power supply. For MBH 6 models, a faulty heating element could also be the cause, which would require replacement by an authorised technician.
C
Catherine SmithAug 22, 2025
What to do if clage MBH switches on but water remains cold?
- M
  Maureen ParkerAug 23, 2025
  If the water remains cold even though your clage Water Heater switches on, it could be due to an incorrect electric supply, no voltage, or a faulty heating element. Check the electric supply and the fuses in the electrical installation. If the heating element is faulty, it should be replaced by an authorised technician.
K
kempmelissaAug 26, 2025
Why is my clage Water Heater running but the water is still cold?
- E
  Elizabeth MartinezAug 26, 2025
  If your clage Water Heater switches on but the water remains cold, there could be a few reasons. It might be due to an incorrect electrical supply, so check the electric supply. Another possibility is that there is no voltage; in this case, check the fuses in the electrical installation. Lastly, it could be a faulty heating element, which would need to be replaced by an authorised technician.
L
lisamullinsAug 28, 2025
What to do if my clage MBH doesn't switch on and the water stays cold?
- B
  Brian GrahamAug 28, 2025
  If your clage Water Heater doesn't switch on and the water remains cold, it could be due to a few reasons. The water connections might be mixed up, so check the installation. Another possibility is that the water flow pressure is too low; in that case, check the water flow setting, open the angle valve further, and check the water pressure. Lastly, there could be dirt in the pipes; remove dirt from the inlet and outlet pipes.
R
richardsonjoshuaAug 30, 2025
Why does the hot water temperature vary in my clage Water Heater?
- A
  Amy MillsAug 30, 2025
  If the hot water temperature from your clage Water Heater varies, it could be due to fluctuations in water pressure or variations in the supply voltage. To address this, try to stabilize the water flow pressure and check the supply voltage.
D
daviddanielsSep 2, 2025
Why does my clage MBH keep switching on and off?
- D
  Donna TaylorSep 3, 2025
  If your clage Water Heater switches itself on and off, it is possible that the water pressure is fluctuating or the flow rate is too low. To solve this, remove any dirt, increase the water flow pressure, close other taps, and open the angle valve further.
L
Lori WalkerSep 5, 2025
Why is the water flowing slowly from my clage MBH?
- C
  Cody MooreSep 5, 2025
  If water flows more slowly than expected from your clage Water Heater, it might be because the special tap aerator is not fitted, the water pressure is too low, or there is dirt in the pipes. Try fitting the special tap aerator, check the water flow pressure, and remove any dirt from the filter, angle valve, and tap.
J
James LopezSep 7, 2025
How to fix a clage MBH when no water flows?
- E
  Edward AllenSep 8, 2025
  If no water flows from your clage Water Heater, the water supply may be turned off. Open the main water valve and angle valve.
W
woodvictoriaSep 12, 2025
Why does the hot water temperature fluctuate on my clage MBH?
- C
  Christopher LittleSep 12, 2025
  If the hot water temperature from your clage Water Heater varies, it could be due to fluctuating water pressure; try to stabilise the water flow pressure. Another cause might be a varying supply voltage, so check the supply voltage.