Clarion ADB340MP Service Manual

ADB340MP
ADB341MP
- 9 -
653-0430-32 TC94A14FA Digital Servo Processor for CD
Terminal Description
pin 1: B CK O : O : Bit clock output.
pin 2: LR CK O : O : LR clock output.
pin 3: A DATA O : O : Audio data output.
pin 4: DIGI OUT : O : Digital data output
pin 5: IPF OUT : O : IP flag output.
pin 6: VDD : - : Positive supply voltage.
pin 7: VSS : - : Negative supply voltage.
pin 8: SB OK O : O : Sub code Q data CRCC OK signal output.
pin 9: SUB C CK :I/O: Sub code data P to W clock input/output.
pin 10: SUB C DATA : O : Sub code data P to Q output.
pin 11: SF SY O : O : Playback frame synchronize signal output.
pin 12: SB SY O : O : Sub code block synchronize signal output.
pin 13: IO0 :I/O: Universal input/output port.
pin 14: IO1 :I/O: Universal input/output port.
pin 15: P VDD : - : PLL positive supply voltage.
pin 16: PH DIF : O : EFM-PLCK Phase difference signal output.
pin 17: T MAX O : O : T max judgment output.
pin 18: PLL LPF NI : IN: PLL LPF inverted input.
pin 19: PLL LPF O : O : PLL LPF output.
pin 20: P Vref : - : PLL reference voltage.
pin 21: VCO FILTER : O : Loop filter for VCO.
pin 22: A VSS : - : Analog ground.
pin 23: SLCO : O : Output of internal DAC for data slice level
generation.
pin 24: RF IN : IN: RF signal input.
pin 25: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 26: RF RP CT : IN: RERP center level input.
pin 27: RF RP Z IN :IN: RF RP signal input for zero cross.
pin 28: PR RP IN : IN: RF ripple signal input.
pin 29: F E :IN : Focusing error signal input.
pin 30: SBAD : IN: Sub beam add signal input.
pin 31: T E : IN: tracking error signal input.
pin 32: TE Z IN :IN : Tracking error signal inpur for zero cross.
pin 33: Fo EQ OUT : O : Focus equalizer output.
pin 34: T EQ OUT : O : Tracking equalizer output.
pin 35: Vref : - : Reference voltage.
pin 36: RF GAIN : O : RF gain control signal output.
pin 37: TR B CNT : O : Tracking balance control signal output.
pin 38: APC ON : O : APC ON signal output.
pin 39: A VDD : - : Positive supply voltage for the Analog sec-
tion.
pin 40: Fe EQ OUT : O : Feed equalizer output.
pin 41: DISC EQ O : O : Disc equalizer output.
pin 42: VSS : - : Negative supply voltage.
pin 43: VDD : - : Positive supply voltage.
pin 44: TEST : IN: For the test.
pin 45: X VSS : - : Master clock analog ground.
pin 46: X IN :IN : Crystal connection.
pin 47: X O : O : Crystal connection.
pin 48: X VDD : - : Clock power supply.
pin 49: VSS : - : Negative supply voltage.
pin 50: R CH OUT : O : Right channel data output.
pin 51: VDD : - : Positive supply voltage.
pin 52: Vref : - : Reference voltage.
pin 53: L CH OUT : O : Left channel data output.
pin 54: VSS : - : Negative supply voltage.
pin 55: Z DET O : O : 1bit DAC zero flag output.
pin 56: VSS : - : Negative supply voltage.
pin 57: BUS 0 :I/O: MPU Data input / output.
pin 58: BUS 1 :I/O: MPU Data input / output.
pin 59: BUS 2 :I/O: MPU Data input / output.
pin 60: BUS 3 :I/O: MPU Data input / output.
pin 61: BU CK IN :IN : MPU Data clodk input.
pin 62: CCEI : IN : Chip enable input.
pin 63: RSTI : IN : Reset signal input.
pin 64: VDD : - : Positive supply voltage.
653-0429-15 BA3430FS Tape Pre-amplifier with Blank Detector
24
23
2213 141516171819 202112
111098765432
1
COMPARE
Detect Out GND Bias VCC Mute Sw Mute Out 2 Metal Out 2 Metal Sw Eq Out 2 NFB 2 Input B 2 Input A 2 Input Sw
Mute Out 1
Metal Out 1
Eq Out 1
NFB 1
Input B 1
Input A 1
Time Const
NFB
NFB
Sense Sw
LPF
LLL
L
IN2
V
Z
V
CC
1
IN1
GND
6
4
7
P2
9
OUT2
10
V
CC
2
8
OUT1
2
P1
3
5
1
LOGIC CONTROL
PRE-DRIVWE
653-0429-16 LB1641 Bidirectional Motor Driver
653-0429-19 LA6458M Dual Operational Amplifier
1 2 3 4
VEE
VCC 8
7 6 5

Clarion ADB340MP Specifications

General

Brand	Clarion
Model	ADB340MP
Category	Car Receiver
Language	English