COMPONENTS
PE-2561B-A/PE-2561K-A/B
Source unit 1
Mounting bracket 300-4976-00 1
300-7742-00 1
DCP ca se 335-6035-20 1
Escutc he on(O U T-ES) 370-6037-00 1
Extension lead 854-6349-50 1
Remo te control un i t RCB-164-600 1
Batter y( SU M- 3) 1
Parts bag
Removal key 331-2497-00 2
Scr ew 716-0496-01 1
Scr ew 716-0872-11 1
To engineers in charge of repair or inspecti-
on of our products.
Before repa ir or inspection , make sure to follow the inst-
ructions so that customers and Engineers in charge of
repair or inspection can avoid suffering any risk or injury.
1. Use specified parts.
The system uses parts with special safety features against fire
and voltage. Use only parts with equivalent characteristics when
replacing them.
Theuseofunspecifiedpartsshallberegardedasremodelingfor
which we shall not be liable. The onus of product liabilit y (PL) shall
not be our responsibility in cases where an accident or failure is as
a result of u nspecified parts being used.
2. Place the parts and wiring back in their origin al positions after
replacement or re-wiring.
For proper circuit construction, use of insulation tubes, bonding,
gaps to PWB, etc, is involved. The wiring connection and routing to
the PWB a re specially plan ned using cla mps to keep away from
heated and high voltage parts. Ensure that they are placed back
in the i r original positions after repai r or inspection.
If extended damage is caused due to negligence during repair, the
legal responsibility shall be with the repairing company.
3. Check for safety after repair.
Check that the screws, parts and wires are put back securely i n
their original position after repair. Ensure for safety reasons there
is no possibili ty o f secondary ploblems around the repaired spots.
If extended damage is caused due to neglige nce of repair, the
legal responsibility shall be with the repairing company.
4. Caution in removal and making wiring connection to the parts for
the automobile.
-
-
Disconnect the battery terminal after turning the ignition key off.
If wrong wiring connections are made with the battery connected,
a short circuit and/or fire may occur. If extensive damage is
caused due to negligence of repair, the legal responsibility shall
be with the repairi ng co mpany.
5. Cautions regar ding chi ps.
Do not reuse removed chips even when no abnormality is ob-
served in their appearance. Always replace them with new ones.
(The chip parts include resistors, capacitors, diodes, transistors,
etc). The negative pole of tantalum capacitors is highly suscep-
tible to heat, so use special care when replacing th em and
check the operation afterwards.
6. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the iron tip
temperature is around 270 C. Take care not to apply the iron tip
repeatedly (more than three times) to the same patterns. Also
take care not to apply the tip with force .
7. Tur n the unit OFF during disassembly and par ts replacement.
Recheck all work bef ore you apply power to t he unit.
8. Cautions in chec king that the optical pickup lights up.
The laser is focused on the disc r eflection surface th rough the
lens of the optical pickup. When checking that the laser optical
diode lights up, keep your eyes more than 30cms away from
the lens. Prolonged viewing of the laser within 30cms may dam-
age your eyesight.
9. Cau tions in handling the optical pickup
The laser diode of the optical pickup can be damaged by elec-
trostatic charge cau sed by your clothes and body. Make sure
to avoid electrostatic charges on your clothes or body, or dis-
charge static electric ity before handling the optical pickup.
9-1.Laser diode
The laser diod e te rm i nals are shorted for tran sportation in
order to prevent electrostatic damage.
After repl acement, open the shorte d circuit. When removing
the pickup from the mechanism, short the terminals by sol-
dering them to prevent this damage.
9-2.Actuator
The actuator has a powerful magnetic circuit. If a magnetic
material is put close to it, its characteristics will change. En-
sure that no foreign substances enter through the ventilation
slots in the cover.
9-3.Cleaning the lens
Dust on the optical lens affects performance. To clean the
lens, apply a small a mount of isopropyl alcohol to lens paper
and wipe the lens gently.
FEATURES
1. MP3 and WMA File Playable with ID3-TAG and WMA-TAG Display
2. DUAL ZONE Control with Ded icated RCA Line Lev el Ou tp ut s
3. 1-Bit D/A Converters and 8-Times Oversampling Digital Filter
4. Z-ENHANCER PLUS for Sound Creation with 4 Adjustment Modes
(2-Ban d P.EQ)
5. MAGNA BASS EX for Dynamic Bass Tuning, Volume Level
Dependent
6. Flip Down Detachable Aluminum Face w ith 80-Variable Color LC
Display and Control Buttons
7. Screen Saver with User Programmable MESSAGE
INFO RM AT IO N
8. CeNET with Balanced Audio Line Transmission and Dynamic
Noise Canceling
CHANGING THE RECEPTION AREA
Model PE-2561B-A(U.S model) is initially set to USA frequency
intervals of 10kHz for A M and 200kHz for FM. When us ing it
outside the USA, the frequency reception range can switched to
the intervals belo w.
Sett ing the reception area
1. Press the [BND] butt on and select the desir ed radio ban d
(FM or AM).
2. While pressing the [A-M] button and hold the number "2" of t he
[DIRECT] button for 2 seconds or longer, the reception area
switches from inside the USA to outside the USA.
3. While pressing the [A-M] button and hold the number "1" of the
[DIRECT] button for 2 seconds or longer, the reception area
switches f rom outside the USA to insi de the U SA.
* Any station preset memories are lost when the reception
area is changed.
DXZ735MP
To Next Page
Loading...
