Clarion DXZ778RUSB - Page 17

Basic Operations
English
17
DXZ778RUSB
Adjusting Sound Setting
Mode
● Setting the preset setting
This function allows you to recall, save or
initialize the sound settings.
If your speaker system is “ 3WAY ” or “ 2WAY ”,
you can store and recall up to three adjustments
you have made to “ P.EQ ON/OFF ”, “ X-OVER ”,
“ T ALIGNMENT ”, “ SPEAKER GAIN ”.
LOAD : To recall the stored sound settings.
SAVE : To save the sound settings.
INITIAL : To initialize the sound settings.
The load and the save can be adjusted as
follows.
2-1. Select “ PRESET ”.
3-1. Press the [ ] button.
3-2. Push the [ SEEK PANEL ] leftward or
rightward and select from:
“ LOAD ” ↔ “ SAVE ” ↔ “ INITIAL ” ↔
“ LOAD ”...
3-3. Push the [ P.CH ] button upward or
downward to adjust the load and the save.
LOAD :“ SELECTING 1 ” to “ SELECTING
3 ” (The factory default setting is
“ SELECTING 1 ”)
SAVE :“ 1 ” to “ 3 ” (The factory default
setting is “ 1 ”)
3-4. Press and hold the [ ] button to
store into memory.
( LOAD : Press and hold the button for 1
second or longer.
SAVE : Press and hold the button for 2
seconds or longer.)
● Setting the all seat
The setting of “ T ALIGNMENT ” and “ SPEAKER
GAIN ” temporarily returns to the factory default
setting. When the setting that is adjusted for the
driver's seat returns to the factory default
setting, a sound suitable for all seats is
provided.
∗ The factory default setting is “ OFF ”.
2-1. Select “ ALL SEAT ”.
3-1. Push the [ P.CH ] button upward or
downward to select “ ON ” or “ OFF ”.
● Setting the X-OVER
This function allows you to adjust the speaker
setting such as cutoff frequencies or slope
matched to the speakers you are using.
(Crossover).
2-1. Select “X-OVER”.
3-1. Press the [ ] button.
3-2. Push the [SEEK PANEL] leftward or
rightward and select from:
To change sound setting mode
1. Press and hold the [ ] button for 2
seconds or longer and select the sound
setting mode to adjust.
2. Push the [SEEK PANEL] leftward or
rightward to select the “item name”.
When speaker system is “NORMAL”:
“PRESET” ↔ “ALL SEAT” ↔ “T
ALIGNMENT” ↔ “P.EQ ON/OFF” ↔ “EQ
SELECT” ↔ “SUB WOOFER” ↔
“PRESET”...
When speaker system is “3WAY”:
“PRESET” ↔ “ALL SEAT” ↔ “X-OVER”
↔ “T ALIGNMENT” ↔ “SPEAKER GAIN”
↔ “P.EQ ON/OFF” ↔ “EQ SELECT” ↔
“SUB WOOFER” ↔ “PRESET”...
When speaker system is “2WAY”:
“PRESET” ↔ “ALL SEAT” ↔ “X-OVER”
↔ “T ALIGNMENT” ↔ “SPEAKER GAIN”
↔ “P.EQ ON/OFF” ↔ “EQ SELECT” ↔
“PRESET”...
∗ In the case of item names appearing with
the “ENT” suffix, after the item name, the
[] button must be pressed to display
the setting value.
∗ After completing settings, press the
[]
button to return to the previous mode.
• HIGH
• HPF
• HPF SLOPE
• PHASE
• MID
• LPF
• LPF SLOPE
• HPF
• HPF SLOPE
• PHASE
• SUB-W
• LPF
• LPF SLOPE
• HPF
• HPF SLOPE
• PHASE
• HIGH
3WAY mode
(High pass filter)
(HPF slope)
(Phase)
(Front speaker (high))
(Front speaker (mid))
(Subwoofer)
(Low pass filter)
(LPF slope)
DXZ778RUSB_EN.book 17 ページ ２００６年１２月２６日 火曜日 午後２時２５分