Clarion Net DXZ638RMP User Manual

DXZ638RMP 13
English
Adjusting the tone
Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button,
the item changes as following order:
● When “BASS BOOST” is set
“B-BOOST” ➜ “BAL 0” ➜ “FADER 0” ➜
Last function mode.
● When “IMPACT” is set
“IMPACT” ➜ “BAL 0” ➜ “FADER 0” ➜ Last
function mode.
● When “EXCITE” is set
“EXCITE” ➜ “BAL 0” ➜ “FADER 0” ➜ Last
function mode.
● When “CUSTOM” is set
“BASS” ➜ “TREBLE” ➜ “BAL 0” ➜
“FADER 0” ➜ Last function mode.
● When “Z+ OFF” is set
“BAL 0” ➜ “FADER 0” ➜ Last function
mode.
Adjusting the bass (Gain,
Frequency, Q-curve)
This adjustment can be performed when the Z-
Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “BASS”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the bass; turning it counterclock-
wise attenuates the bass.
∗ The factory default setting is “B
ÅÅ
ÅÅ
Å
GAIN 0
ÎÎ
ÎÎ
Î
”.
(Adjustment range: –6 to +8)
3. Press the [d] or [a] button to select
“B
ÅÅ
ÅÅ
Å
FREQ 50
ÎÎ
ÎÎ
Î
”.
Turninng the [ROTARY] knob clockwise or
counterclockwise to select the frequency.
∗ The factory default setting is “B
ÅÅ
ÅÅ
Å
FREQ
50
ÎÎ
ÎÎ
Î
”.(Adjustment 50/80/120 Hz)
4. Press the [d] or [a] button to select “B
ÅÅ
ÅÅ
Å
Q 1
ÎÎ
ÎÎ
Î
”.
Turninng the [ROTARY] knob clockwise or
counterclockwise to select the Q-curve.
∗ The factory default setting is “ B
ÅÅ
ÅÅ
Å
Q 1
ÎÎ
ÎÎ
Î
”. (Ad-
justment 1/1.25/1.5/2)
5. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the treble (Gain,
Frequency)
This adjustment can be performed when the Z-
Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “TREBLE”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the treble; turning it counterclock-
wise attenuates the treble.
∗ The factory default setting is “T
ÅÅ
ÅÅ
Å
GAIN 0
ÎÎ
ÎÎ
Î
”.
(Adjustment range: –6 to +6)
3. Press the [d] or [a] button to select
“T
ÅÅ
ÅÅ
Å
FREQ 12k
ÎÎ
ÎÎ
Î
”.
Turninng the [ROTARY] knob clockwise or
counterclockwise to select the frequency.
∗ The factory default setting is “T
ÅÅ
ÅÅ
Å
FREQ 12k
ÎÎ
ÎÎ
Î
”.
(Adjustment 8 kHz/12 kHz)
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the balance
1. Press the [A-M] button and select “BAL 0”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the sound from the right speaker;
turning it counterclockwise emphasizes the
sound from the left speaker.
∗ The factory default setting is “BAL 0”. (Adjust-
ment range: L13 to R13)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the fader
1. Press the [A-M] button and select “FADER 0”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the sound from the front speakers;
turning it counterclockwise emphasizes the
sound from the rear speakers.
∗ The factory default setting is “FADER 0”. (Ad-
justment range: F12 to R12)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Basic Operations

Clarion Net DXZ638RMP Specifications

Radio Section

FM receiving frequency	87.5 to 108 MHz
MW receiving frequency	531 to 1602 kHz
LW receiving frequency	153 to 279 kHz

CD Player Section

frequency response	10 Hz to 20 kHz
signal to noise ratio	100 dB
dynamic range	95 dB

General Specifications

output power	4 ✕ 27 W
power supply voltage	14.4 V DC
power consumption	Less than 15 A

Weight and Dimensions

weight of main unit	1.3 kg
dimensions of main unit	178 (W) ✕ 50 (H) ✕ 157 (D) mm
speaker impedance	4 Ω